Search results

  1. jammer84_03

    HELP!!! tko600 crossmember not fitting

    p.s. i clearanced the exaust hanger when i had the 3550
  2. jammer84_03

    HELP!!! tko600 crossmember not fitting

    well i called d and d and they said it should fit no prob. i unbolted the x pipe at the headers and now i am going to just bolt them back again and go from there. the exaust hanger fit and i clearanced the double hump c memeber. it slides all the way back and will fit, but it bends the exaust...
  3. jammer84_03

    HELP!!! tko600 crossmember not fitting

    ok...so i took out my old 3550 and got the new tko 600, now when i got it all bolted back up i go to put the trans crossmember up and it wont go up without bending the exaust really bad. is there a special crossmember that i ahve to buy to make this fit?
  4. jammer84_03

    Idle staying at 2,000 RPM

    with the car sticking at 1500 while comming to stop is built into the programming on the computer. it was made to not drop the rpm immediately and cause more strain on the trans and engine. aem actually has this as a programable option where it wont do it after you go below rolling at 25mph. i...
  5. jammer84_03

    still no start

    sure you have fuel pressure?
  6. jammer84_03

    c-clip eliminators

    im looking to do a complete rear end upgrade next week after i get me nex axles and diff and gears. the question being. i do alot of raod racing. and i heard elim the c clip will help with strength in the read end, but i heard it leaks fluid on hard cornering?
  7. jammer84_03

    Best Ignition for the Stang

    msd is not the greatest in teh world. when aem came out with their programmable ecu msd was found to have very bad tolerances. i would try a different company just based of what research i have done into the msd branding and what products you are actually getting!
  8. jammer84_03

    crushed rice!

    i have one thing to say about ricers. after being around them i have no respect. now i do have respect for tuners. there is a huge difference between the two ricers is a "lifestyle", tuning is taking what ya got and going full tilt boogie and making it respectible with out the body kit...
  9. jammer84_03

    Anyone in here running 17 inch saleen replica's?

    i've been trying to find 17x10.5 inch replicas. no where to be found!
  10. jammer84_03

    Please help on getting GT40 irons prepped.....

    i did my own port job on my gt40 irons. its not hard to do at all if you got a lil patience. just match up the intake gasket.... usually a fel1250. paint the dye one the surface of the intake side and scribe your line from the gasket. then take a good porting burr and bring it out. just take...
  11. jammer84_03

    tko 600 rr clutch

    well...checked the site. they didnt have any specifices. i just know i have to have a 26 spline unit in the 10.5". all the 4.6 stuff is 11" i believe
  12. jammer84_03

    tko 600 rr clutch

    i got a huge discount at a local place i cant pass up and they got 13 in stock. i was just looking at summit for a 26 spline and i wasnt for sure. i didnt think to check their site though
  13. jammer84_03

    tko 600 rr clutch

    well, as i posted before i blew up my road race version of the tremec 3550 :bang: . (anyone wanna make an offer on a tranny that need bearings and a third gear pm me. its got the road race spec gearing...great for the street) anyways im about to just pony up and get a tko 600 and get the road...
  14. jammer84_03

    306 or 331??

    i threw the 347 in the middle...but his original q of the 306 or 331.... i was saying no replacemnt for displacement to that... as for the 347 i personally wont do one becuase of the ringing issues with the wrist pin. personally when i get the new boss block, im just going to get the stroker...
  15. jammer84_03

    306 or 331??

    i would go 331.... 347 are great except for the ring land. no replacement for displacement!!!!!
  16. jammer84_03

    Which Cylinder Heads?

    honestly...i would spend the extra coin and just get the edelbrock vic jr. head to match... have the lower matched to the heads and you wont be disapointed...im going full vic jr ion my next engine...need the flow for my turbo
  17. jammer84_03

    FRPP Aluminum Driveshaft U-joints...

    rick...do you have that part number for future ref? im about to do the same. i was actually looking at the lakewood pieces
  18. jammer84_03

    Drivetrain vibration

    t/o bearing?
  19. jammer84_03

    Interior Cleaning

    never use armor all!!!! those are the worst products ever!!!!! its a shops worst nightmare to learn that thats what a customer is using. depending on what type of surface you are cleaning there is a different product. 3m or meguiars has some of the best products for regular vinyl and plastic...
  20. jammer84_03

    frame rails?

    ya...i forgot to type that in the post...lol. im looking for a place so i can compare prices im getting from a guy that said he can do it. that or just repair the ones i have. i am going to take alot of pics. i plan on routing the s&p shaker wiring in the tranny tunnel. most of the wiring will...
Top Bottom
Back
Forums
Menu