Search results

  1. SwAmPf0x

    1.7 RR and B303 Cam?

    That was on the intake, exhaust appeared to have more so I didnt bother to measure
  2. SwAmPf0x

    Can't Get Head off! Quick..Help!

    You have removed the lower intake right? sounds like you havent by that statement
  3. SwAmPf0x

    1.7 RR and B303 Cam?

    I had ~ .200" clearance with that setup, in other words....plenty
  4. SwAmPf0x

    Ordering 3g alternator, but have a question

    The long wire is probably for a rear battery/ kill switch setup, where the charging wire has to be run to the back for the kill switch to kill the car, It doesnt say how long either is though, best bet would be to call and ask unless someone who has bought from them chimes in here....
  5. SwAmPf0x

    Factory A/C delete brackets....part numbers??

    Just buy the kit.... http://store.summitracing.com/partdetail.asp?part=FMS%2DM%2D8511%2DA50
  6. SwAmPf0x

    Looking for sound clip- Carb 302, LT's, prochamber, 2 chamber flows

    I have that exact combo except Mac Headers instead of Hooker's, should sound the same though, no sound clip but I might could let you hear it over the phone if that would do you any good :shrug:....PM me your number if you like
  7. SwAmPf0x

    Running Hot-baffled!!

    Yes the rear passages should be open and the front ones blocked, this usually means one gasket goes on upside down compared to the other, easy to get wrong if you dont pay attention, I can see the part number on my set, little tab sticks out at the lower front corner of each head, Fel Pro 8548PT2's
  8. SwAmPf0x

    Running Hot-baffled!!

    What gaskets did you use? you may be able to tell if one is on wrong by looking at the tab that sticks out on the front corner, Fel-Pro's have the gasket number printed there, I looked at mine....passengers side the number is down, drivers side is up.
  9. SwAmPf0x

    Running Hot-baffled!!

    New motor Im guessing? has it run hot since new? if so you may have the head gaskets on wrong, are you sure that the "front" marking on the gaskets is to the front of the engine on both gaskets
  10. SwAmPf0x

    Will this cam work with my "stock" heads?

    They should be able to handle the lift, valve float may be an issue though, what is the advertised duration?
  11. SwAmPf0x

    FMS headers fit on..

    Yes they will, only difference in them is the primaries come out a little farther before turning toward the collector
  12. SwAmPf0x

    Friend is annoying. Read on.

    It will be with .040 pistons, I think I could live with that though :)
  13. SwAmPf0x

    Cold temps and no antifreeze......

    Definately put antifreeze in it, actually a 50/50 mix will have a lower freezing temp than 100% antifreeze
  14. SwAmPf0x

    GT-40 P: what-Plugs,wires,pushrods,headers do i need???

    Stock length is 6.272", I did install the 1.7's at the same time, but I tried the stock rockers also and the preload still wasnt right. I got the pushrods from Summit, of course try the stock length first, they "should" work, and a custom length set will run about $90, milling .030 off the...
  15. SwAmPf0x

    GT-40 P: what-Plugs,wires,pushrods,headers do i need???

    Autolite 764's, if you need a colder plug use 103's The Mac Longtubes will work, Im using them I made my own spark plug wires, bought a roll of MSD super conductor wire, and 2- 90 degree terminal/boot kits from summit, if you need me too Ill list everything I bought for you. you can use a...
  16. SwAmPf0x

    need starter help

    What year car? they changed starters in the early 90's to one with a starter mounted solenoid, have you replaced the solenoid in the picture also?
  17. SwAmPf0x

    How to improve brakes on 86 LX 5.0

    http://svo73mm.cjb.net
  18. SwAmPf0x

    need starter help

    Do you have a test light or volt meter? if so, at the starter relay check for power on the wire going to the starter with the key in the "start" position, of course youll need a helper to do this, might take a look at your negative battery cable too, especially where it attaches to the block
  19. SwAmPf0x

    mounting engine to stand

    Doesnt the mounting plate come out of the stand? bolt it to the engine first then slip in into the stand, no having to hold it that way while your trying to get the bolts in. thats the way mine works anyway
  20. SwAmPf0x

    Steeda Rear Quarter Window covers

    I agree they suck, dont waste your money, repairing the existing moulding is a much better option
View older results
Top Bottom
Back
Forums
Menu