Search results

  1. fredfifty

    Engine Heater Tube Sensor

    the wire harness sensor has both plug types (see pic) im guessing i could use either one on the wire harness? or should i swap the round sensor and put the square sensor on the motor going in?
  2. fredfifty

    Engine Heater Tube Sensor

    Hey guys, swapping my motor and came across this issue. The motor im taking out (red fuel rails) has a square heater hose sensor, see pic. The motor replacing it has the roundish sensor, see pic. The harness in the car right now has both plug types (one is tapped in, see pic) Do those...
  3. fredfifty

    What's Your Daily Driver?

    got a great deal on a 2016 STi as a DD...just cant stand the huuuuge wing lol
  4. fredfifty

    Swapping Injectors/Rails

    Im gonna be swappin motors soon (302 hci > 302 stock), and i wanted to know if i could swap over my 24lb injectors and aftermarket fuel rail (not sure of brand, but rails are red) to my stock 302? Or could i just swap my 24 lbers over to the stock engine with stock fuel rails? And should i...
  5. fredfifty

    Engine Coolant leak - Spraying from Passenger Side

    change the hose
  6. fredfifty

    Pulling out that 5.0 engine

    glad i found this! If im only taking the motor out, im assuming i dont need to touch the h pipe, trans, or drive shaft?
  7. fredfifty

    Engine 302 to 302 swap (motor removal/install)

    HCI 302 has a bad piston ring or valve stem seal....leaning towards piston ring. So i figure i will pull it out and rebuild it slowly.. the stock motor is going in because ca smog is a pain in the ass and i want to be able to drive the car while the motor is getting rebuilt
  8. fredfifty

    Engine 302 to 302 swap (motor removal/install)

    I plan on taking out my HCI 302 to replace it with a stock 302. Basically a 92 302 to an 89 302. Can someone give me some detailed step by steps in doing so? I have a tremec 3550 which i will leave in. I have the hoist. Just need someone to guide me with the details. I hear its easy, but...
  9. fredfifty

    Fox Coupe Trunk Lid Aligning

    I had the passenger side one on, but I don't have a driver side one, still closed lower on the passenger side. I took it off and and still closed the same. I don't think the rubber bumper I had one was even doing anything to aid in the alignment.
  10. fredfifty

    Fox Coupe Trunk Lid Aligning

    For the life of me, i cant find a "how-to" on how to align/adjust a fox coupe trunk rear deck lid...is there a technique or a specific pattern to follow? i see all the bolts to make the adjustment (latches, hinges) but i cant seem to do it. my deck lid, when closed, is lower on the driver...
  11. fredfifty

    Pypes Exhaust

    arise.... for the flow tubes (muffler to mid-pipe)...they have bends, now does that mean the flow tube should be twisted to a certain position (bend facing driver side or passenger side)? i just installed the pypes violator catback w/3" tips. tips hang past the bumper on my 92 LX about a...
  12. fredfifty

    Exhaust Leak At O2 Bung

    did wet test, pressure held at 150, damn.
  13. fredfifty

    Exhaust Leak At O2 Bung

    View: https://youtu.be/ZMDvoHK6J5Q here is test on 8 cylinder
  14. fredfifty

    Exhaust Leak At O2 Bung

    Here is #8 plug
  15. fredfifty

    What's Your Daily Driver?

    16 STi and 13 Sienna SE (dont laugh)
  16. fredfifty

    Exhaust Leak At O2 Bung

    Alright ran compression....by cylinder in numerical order 140/140/144/150/142/140/142/however number 8 does not hold pressure. It will go up as the car is cranked (up to about 160 or so, then when we stop cranking, the gauge pressure drops slowly to zero). We did the test to #8 a few times, same...
  17. fredfifty

    Fuel Can You Id This Fuel Rail?

    I googled it and couldnt find one that matches the one i have in the pic. I thought BBK but the rails i have are round, not rectangular. Anyone know what brand rails these are? (Vague pic i realize but i hope someone can tell me)
  18. fredfifty

    Exhaust Leak At O2 Bung

    Indeed. Thats why im hoping its just a valve seal that went bad just after i put the new plugs in.
  19. fredfifty

    Exhaust Leak At O2 Bung

    Not at all, these were plugs i took out prior. No idea on miles on them....im guessing quite alot....atleast 10-20k miles
  20. fredfifty

    Exhaust Leak At O2 Bung

    3 months/200 miles at most
View older results
Top Bottom
Back
Forums
Menu