Search results

  1. faststang90

    Foxes with Billet Specialties Street Lites

    i think the first pic i had just installed the 9 inch. i had installed new contral arms too and they had to send me some other contral arms because i could not get the wheel base square. the one upper would not screw in and it was holding the rearend off to one side.
  2. faststang90

    Foxes with Billet Specialties Street Lites

    its right on the end of the body. i can go in about 1 inch but the car is on hold for now.
  3. faststang90

    Foxes with Billet Specialties Street Lites

    i have the 15x3.5 on the front and a 15x10 with a 3.5 bs. i had welds on it but they would not clear the rear brakes.
  4. faststang90

    trick flow r heads

    im looking at getting a motor from bennett and it has high ports on it. i asked the guy about going to the R heads and he said that it would be a waste of money. he said they change to the R heads and only picked up a few hp. he said it would not be worth the money to change. the motor im...
  5. faststang90

    opinions on rear seat delete

    i had mine done. its a full race and only has 1 seat ion the car. look here 1987 - 1993 Mustang Hatchback Rear Seat Delete Kit K Dezines 1987 - 1993 Mustang Hatchback Rear Seat Delete Kit with Access Doors : Welcome to K Dezines! or 1987 - 1993 Mustang Hatchback Rear Seat Delete...
  6. faststang90

    billet specialties wheels BS question

    i did the 3.5 rim with 1.750 in bs but i have areospace front brakes
  7. faststang90

    Mini tub kit

    i did the autoweld kit and it was a good fit the only problem i had was the anti roll setup they have. i have a 15x10 rim with a 3.5 bs. i also did the offset lower contral arms. i did the 9 inch that is 3.5 inches shorter than a 8.8 on each side. i have a little more than a inch from the rear...
  8. faststang90

    Rearend not centered?

    its that way stock. the motor any tranny is offset to the passager side.
  9. faststang90

    Removing bellhousing upper bolts

    i lowered the tranny down and got them 2 first and worked my way down. the tranny stayed on the dowels then just worked it off them.
  10. faststang90

    1986 gt, a few ?s

    no both 5 speeds. the stock tranny aod is junk.
  11. faststang90

    1986 gt, a few ?s

    my friends old car had about the same set up and i think a low 12 is what it ran. he had the heads ported. it was a 331 ci. i dont think a stock motor with gt-40 will run a low 12. my old motor was a 306 with canfield fully ported heads, system max intake,30# inj, custom cam,and the fastest i...
  12. faststang90

    DIY junkyard turbo kit

    when i did mine i got a set of headers from them at a swap meet. i had a friend that worked at a exhaust shop so i got off cheaper when his boss was not there. mine 1 header was just a stock header turned around and flipped sides. this is the place that made my headers for a single t-4 turbo...
  13. faststang90

    DIY junkyard turbo kit

    when i said not cheap i was thinking a few hundred dollars. i had to have my carb made for bt, carb hat,fuel reg. i did not go with a ebay waste gate or blow off. i think they was around 500.00 for both. i think if u have 2000.00 -2500.00 u will be good. go to turbomustang.com that is where...
  14. faststang90

    DIY junkyard turbo kit

    a lot i did a single and its not cheap and i was a carb. i did a single t-76 turbo. BUICK GNX 87 3.8L GAR TB0348 BUICK Monte Carlo/Regal 78-83 3.8L carbed GAR TB0348 BUICK Riviera 80-85 3.8L GAR TB0308 BUICK Grand National/T-Type 86-87 3.8L (Intercooled) GAR TB0348 (TA48) BUICK Trans...
  15. faststang90

    flywheel

    just make sure the flywheel is the right size for the t 5 bell housing and it the right balance this should be the right 1 RAM Billet Steel Flywheel - 28 oz (86-95 5.0L) at AmericanMuscle.com - Free Shipping!
  16. faststang90

    Ford 9" vs 8.8"

    that is true. my 9 inch you would never see in a factory car. the input on my car is a 35 spline input.
  17. faststang90

    sub frame connector question

    i say no because the sub frame is going to be the back bone of the car. i think if u screw or rivet the floor u will just be making it weaker.
  18. faststang90

    Ford 9" vs 8.8"

    i went from a 8.8 with 35 spline axles to a 9 inch with 40 spline axles,pro gears, a back brace,35 spile input shaft just because i was doing a big motor with a big turbo and i was being told the 8.8 with that size axles had problems so that y i went with a 9 inch. i was told the spools break...
  19. faststang90

    Time to fabricate, need some pointers please.

    i would make one go to the fender to get cooler air.
  20. faststang90

    Does anyone have these 1 piece headlights

    i did the 1 piece on my 1993 and they are JUNK. they are paint like on the inside and its coming off and its a rull race car that does not get drove on the street.
Top Bottom
Back
Forums
Menu