Search results

  1. drgn5.0

    Catalytic Converter Rattle - Not the Shields

    catco doesn't have a good history in my book, they work fine in a truck but i've got NO good experiences with them in a high performance vehicle.
  2. drgn5.0

    Gapping Autolite plugs

    I wouldn't run platinum plugs in your car, go with regular copper autolites. at .045
  3. drgn5.0

    Driveshaft Vibration - New Alum or ReBalance???

    contact me if you want to pick up a second steel driveshaft instead, i got one and i can probably get ahold of another or two. aluminum went up to 250-260 but you can get a strange chromoly shaft for like 199.99
  4. drgn5.0

    Tell me if my problem is with the TOB or release bearing...

    you considered it might be the stock driveshaft? i can't hear bad throwout bearings unless i'm at idle, not cruising.
  5. drgn5.0

    Whats next!?!?!?!

    i'd probably go with 70 or 75mm, if you plan on getting turbo, s/c later on go with 75. i still run stock tb/egr myself, not a huge power difference, but a definite throttle response. Pro M might have some chrome style maf's, but i prefer c&L.
  6. drgn5.0

    Whats next!?!?!?!

    I'm pretty sure the stage 2 wont clear the stock pistons. so if you want to notch them some more you can. just take like a die grinder or a dremel to em. 255lph pump 76 c&l mass air w/elbow 24's or 30's a AFPR if you don't have one (Kirban) whatever brand tb you want
  7. drgn5.0

    Help me get header bolt off head...stripped bolt?

    try to cut a wrench down enough so it won't hit the tube and you can loosen it.
  8. drgn5.0

    CRAP! Whats this sound like to you..Intake Manifold Prob

    here is an old pic of my motor, the coolant holes are 2 on each head, on each end. i'd put some rtv on each lower intake gasket, to hold it in place around the ports. then put some rtv w/ a healthy amount on each water port, then put some like i was saying on the block, you can see the first...
  9. drgn5.0

    CRAP! Whats this sound like to you..Intake Manifold Prob

    you need to put rtv around the water jackets ( the holes that don't have valves in them) on the heads, and instead of using the front and rear cork gasket for the lower intake to block, you should put some high temp rtv on the block (where those small strip gaskets went) the whole length and let...
  10. drgn5.0

    93 Cobra Intake

    it's built in on the cobra. its a good intake, it's pretty good all around until you start making serious hp. so it all depends on your plans.
  11. drgn5.0

    CRAP! Whats this sound like to you..Intake Manifold Prob

    did you put rtv around the water ports on the cylinder heads?
  12. drgn5.0

    Engine Oil Cooler

    Thanks for the info, Michael. I will definitely check into one of these when my new combo goes together. your car looks sweet. the upper intake on your car looks like it was welded. or am i just seeing things?
  13. drgn5.0

    FMS Aluminum driveshaft=GOOD

    when i had gears installed my stock driveshaft was rusted a ton but it was one of the joints on it. so i got a aluminum unit for 170 put on. i think these steel shafts rust as soon as they are put on the cars, donchya think?
  14. drgn5.0

    Engine Oil Cooler

    guys, how much is that oil cooler from ford? would it be a good one to use with a turbo kit?? I'm gonna be putting one on the car this year, probably a T76GTS.
  15. drgn5.0

    FMS Aluminum driveshaft=GOOD

    This is a decent thought, but in the same theory, the driveshaft would also be out of balance if you spray painted it cause i believe the paint would have more weight to it. i think the real reason is the joints simply go bad on the shaft and need replacement.
  16. drgn5.0

    hey its me again need a short block

    i dig it yo
  17. drgn5.0

    Larocca's is NO GOOD AT ALL!!! STAY AWAY

    this is not the first post about laroccas i've seen concerning bad treatment.. I'd contact a lawyer and see what recourse you have.
  18. drgn5.0

    FMS Aluminum driveshaft=GOOD

    I'm sorry, but this is complete bull. obviously you have never taken one off for a clutch or tranny replacement.
  19. drgn5.0

    Can anyone ID this TB? IS it a 65mm or a stocker?

    not trying to be a smarta$$, but have you measured it??
  20. drgn5.0

    Holley systeMax ll engine upgrade

    uh no, trickflows package is available through summit, check one of the books or their site.
Top Bottom
Back
Forums
Menu