Search results

  1. BarnStang

    Underdash Wiring Help! Photo's

    THought so, the multi connector is for the emergency flasher switch that goes under the dash on a 65 and in the glove box on a 66. Here is an ebay listing that has some adequate pictures...
  2. BarnStang

    Underdash Wiring Help! Photo's

    1966 pictures by Barnstang - Photobucket The color codes are listed in tables on the diagram pages. Don't assume that one color code on one page is the same on another page...meaning the table on each page applies to that page only as a rule of thumb. SOme of the wire numbers are used more than...
  3. BarnStang

    Underdash Wiring Help! Photo's

    The diagram shows the blue w/ red 3 prong connector as wire 19 that is a place to pick up inst illumination-will come on with the light switch. THe other three prong connector shows as wire 140 as a place to pick up accessory power which will provide 12v in ACC and ON positions of the ign...
  4. BarnStang

    overheating issue

    Make sure the lower radiator hose isn't collapsing shut at higher rpms. THere should be a spring in the bottom hose to prevent this. You can run the throttle up and hold it and watch the hose to see if that's happening. Something to check.
  5. BarnStang

    How much would this work cost if done by someone else ....

    Actually, THATS what this forum is all about! :SNSign:
  6. BarnStang

    How much would this work cost if done by someone else ....

    THat's a pretty close estimate. I figured up 16 hrs as a worst case came to $800-$900 But it depends on where you are located/what the average local labor rate is. A lot of that you can do yourself. THats what this forum is about for the most part. You can get a compression tester at Sears...
  7. BarnStang

    Is this put on right?

    It may be on the wrong side, the view in your picture is of the left front looking from the front, here is a picture of my first 66 FB proj of the left front, looking from the back...
  8. BarnStang

    Won't start- (autor) transmission safety switch

    THe switch can also wear out. Iv'e drilled out the rivits, cleaned it and reassembled with machine screws, but the better fix is to just replace it sinces it's repoped now if everything else checks out.
  9. BarnStang

    Master cylinder

    When you bleed the brakes, do you get a good solid stream of brake fluid out the bleeder? And does the pedel drop? Make sure you are getting good pressure at each wheel. A brake presure tester helps, but not absolutly necessary. Do you have a stock distribution block? Is it possible the stupid...
  10. BarnStang

    LED taillights - no blinkers now! UGGGHH

    THe kit should have come with the flasher, it may not "look" like a traditional flasher too. THe one that came in one of the kits we did had a ground wire that needed to be fastened as well. Make sure you check for that too.
  11. BarnStang

    LED taillights - no blinkers now! UGGGHH

    One of the kits we did reqd a seperate power wire be run back to the trunk-the stock wiring would not carry enough current to flash the LEDs. Check the instructions and see. If the instructions don't call for a seperate power wire, you may want to string one outside the car to see if it helps...
  12. BarnStang

    Roush 08 427R Heat Exchanger damaged

    Thanks for the link! Great info. Regardless of the choice I make, I am still over $100 under the cost of the Roush part. I think I will have to subscribe to that forum!
  13. BarnStang

    Roush 08 427R Heat Exchanger damaged

    Haven't looked at Steeda yet, I have John at BBR looking into non-stock replacement options. I figured if I have to spend that much, I might as well get a better heat exchanger... Opps, wrong acronyme...Blow By Racing. I was refering to Booze Brothers Racing in PA, they are a Roush distributor.
  14. BarnStang

    question on driveline angle

    You can notch the floor support for the added clearence. There was a thread awhile back that showed some good pictures. On T-5 conversions, I notch the floor support and weld a flat plate back up into the section that is notched out. Use a heavy plate, at least 3/16" plate. If you don't feel...
  15. BarnStang

    Roush 08 427R Heat Exchanger damaged

    OK, need some help. Wife took the Roush to vist her grandaughter and ran over a retread that came off a truck tire. She was in the center lane with cars on each side and one behind. Couldn't avoid it. Put a hole in the heat exchanger (somehow...). Called the Roush dealer- $670 Dealer says it's...
  16. BarnStang

    Autometer Wiring for 68 Eleanor clone

    Ohhhh...well then, you most likly have to draw a diagram and trace each wire. One wire should gang all the grounds together, one should gang all the gauge illuminatin bulbs together, one will gang all the 12v gauge feeds for the gauges that require 12v (I think all of them will) One will be a...
  17. BarnStang

    Autometer Wiring for 68 Eleanor clone

    The place you got the pod from can't help with a pinout on the connector? i assume you got the pod prebuilt? You may have to trace each wire and pull the instructions off the Autometer site to map out you own pinout diagram. If someone were to have the pinout, they will need to know who makes...
  18. BarnStang

    Tie rod ends

    Try www.discbrakeswap.com Dennis may be able to help sort out what you have. Was the car originally a 6 cyl car? It sounds like you have 6 cyl steering gear. Generally the 6 cyl cars had 4 lug spindles. Do you have 5 lug spindles but don't know what they came off of? (V8 manual steering...
  19. BarnStang

    Not getting 12volts from ignition switch

    WHat harness did you install? If you are doing an EFI swap, then things are going to be a little different. Is the under dash harness the original factory harness? If so, there is one wire that is switched 12v coming off the ign switch. On the 64 1/2 it should be a red with green strip wire...
  20. BarnStang

    Intake heater hose fitting size

    THe restriction is the extended tube sticking down in the water stream. I found the thread from the 5.0 forum. Read past the 5.0 tech on the heater core down to the part about the flow restrictor. THere are pictures father down Mustang THis will allow you to use a regular AN elbow without...
Top Bottom
Back
Forums
Menu