Search results

  1. nancygrl

    Need some advice again sorry guys...

    Hey I've done all that (except for the CC Plates, going to install when car is down for the winter). If this girl can do it, you should have no problems either. There's plenty of good procedures out there. Print 'em out or bring the laptop in the garage with you and you should be ok.
  2. nancygrl

    crackling, loose bolt sounding noise behind airbag

    Ah...sorry. Ummm.....yep there's all sorts of noises with our SN-95's as stated above. Hey I found a procedure to remove the thing. It should at least help you get at the airbag and see what's going on back there, Hope it helps. Module, Passenger Side Air Bag Removal 1.Disconnect battery...
  3. nancygrl

    crackling, loose bolt sounding noise behind airbag

    Well the airbag is held on with 2 small bolts. The bolts that are behind 2 caps that you access from the sides of the steering wheel. But if it's not that and the steering wheel itself is tight, it might be the rack n pinion bushings that are worn (common problem).
  4. nancygrl

    resurfacing drilled & slotted rotors

    I've read that it can be done. Other than that, no personal experience.
  5. nancygrl

    a/c question

    Well, I had a similar issue on my 99 GT. The tabs on the cable connector that plugs into the compressor were broke and the cable was just hanging. Don't know if that the case here, but worth a quick look.
  6. nancygrl

    Your Mustang Ownership History...lets share!

    Well I am just into Muscle cars, ever since I can remember. Sorry guys but this girl likes Camaro's and Mustangs. :rolleyes: I've been told I'm an enigma since I have both a Camaro and Mustang. What can I say I love 'em both. :flag: While I'm on only my 4th Mustang. I'm on my 5th Camaro...
  7. nancygrl

    high pitch squeeling at 1700 rpms-need help

    I had similar squeek, I changed the serp. belt but squeek was still there. So I changed the idler pulleys they are inexpensive enough and easy to do. Now no annoying squeek. Very glad it wasn't the water pump or ac :nice:
  8. nancygrl

    How to remove rear seats???

    The bottom part is really easy. There's 2 pushbutton release about 5 inches from each end along the bottom of the lower seat cushion where mounts to the car. I had run a flat blad screwdriver across until I hit the side of the release and then moved it to the front and pushed the release button...
  9. nancygrl

    Cruisin Concepts Wheels

    Unless tirerack is running a special...they don't have free shipping. :eek: I stopped using them because when you add up the shipping charges it ends up being more. At least for the things I've shopped for in the past. I bought the 17x10.5 hypercoated wheels and sumi's from AM because they were...
  10. nancygrl

    ZMAX

    not a big fan of royal purple either. have not had any luck with their products.
  11. nancygrl

    KYB GR2 shocks

    Don't know why they aren't carrying them anymore. Tire rack has the quads KG4521 normally $39 they on special for $37 each but they're running low on stock. Summit Racing has them for $33.95. Summit Racing also has 30mm Prothane bushings for $7.95, also has Energy Suspension 2 differnt kits...
  12. nancygrl

    KYB GR2 shocks

    I got my KYB GR2 shocks from Rock Auto. Sucks that they don't have the front's in stock. :( I got all 6 (front,rear, & quads) from them, but that was back in December. Super-duper prices. Couldn't be happier especially since I didn't have to spend what other places charge. :nice: I think...
  13. nancygrl

    Aluminum Driveshaft for 2002 GT Automatic?

    That's what I did on my 99 GT. I bought a new automatic yoke and installed it on my new RFPP aluminum driveshaft. Works great!!! :nice:
  14. nancygrl

    1999 Expedition engine

    IMHO for $100 Yes. Worse case, if you tear it down you can probably make your $100 back and then some.
  15. nancygrl

    Rear Control arm bushing replacement

    Maximum Motorsports has a write up for the lower, but their write-up for the upper is for using their tool, that they sell, to press out the entire stock bushing and press in a new Ford bushing. For using aftermarket upper bushings; drilling out the rubber for the uppers is a PITA! :nonono...
  16. nancygrl

    1999 Expedition engine

    From what I've read in other posts, is that the Windsor has the oil fill on the passenger side, and that the Romeo has it on the driver's side. Also the Windsor should have more valve cover bolts 13 on driver's side and 14 on passenger side, and the Romeo's have 11 on both sides. Almost all...
  17. nancygrl

    suspension noise

    If it's not the ball joints, one of the other things I've read on previous posts, is to check the steering rack bushings. Hope it helps.
  18. nancygrl

    One thousandth post!

    Congrats!!! I'm at 80, guess I have a long way to go before I hit 1k posts :)
  19. nancygrl

    Rear diff fluid change

    Here's the website I used. It's for a bullitt, but procedure is the same. Good website. :nice: BULLITT Archive Differential Fluid Change
  20. nancygrl

    Need help!!!! Removing upper strut bolt!!!!

    +1....use an impact wrench and it'll come right off.
Top Bottom
Back
Forums
Menu