Search results

  1. 67FBack

    67 Super Snake Project

    Front Fenders, Hood, Doors & Trunk Installed
  2. 67FBack

    67 Super Snake Project

    You are welcome to come see it if you want. I see you live close. Edbert, you ever by this way, e-Mail me first and come on by.
  3. 67FBack

    67 Super Snake Project

    Everybody has their favorite color. I have always been partial to red or black. But I have seen so many good looking mustangs here that I had considered changing my decision several times.
  4. 67FBack

    67 Super Snake Project

    A Long Time Coming hah Thnxs. I have been working on this thing about every other day, for over a year now. its been at the body shop since Nov 1st.
  5. 67FBack

    67 Super Snake Project

    Painted .. well partially
  6. 67FBack

    67 Super Snake Project

    Paint Paint is going on the car! Doors & front fenders have been painted And the stripes have all been laid out. Tungsten Silver (new Ford GT color) stripe on Black, with a gold 1/16" pinstripe.
  7. 67FBack

    67 Super Snake Project

    My 427FE My 427FE
  8. 67FBack

    67 Super Snake Project

    Engine Dyno Results Here is the official dyno results. It is set at 10 lbs boost, and 38 degrees timing. The EFI is pulling out 1 degree of timing for every pound of boost. That will kill some horsepower, but I could add a switch and have a second tuning table for a higher octane gas. That is...
  9. 67FBack

    67 Super Snake Project

    Battery Box I bought the Optima Battery and put it in the brackets. My dilemma is.. should I mount it with the side mount cables hidden (to the passenger side) or have them visible from the inside? How about facing rear and closer to the back so they are not that visible? Here is...
  10. 67FBack

    67 Super Snake Project

    Interio Vent Grills I purchased the interior vent grills from Mustang Depot and mounted them in the sail panels. They fit very good.
  11. 67FBack

    67 Super Snake Project

    Radio Bezel I cut the bezel from the back using a cutting disc on my 4" grinder, twisted the piece out, and finished it with a die grinder.
  12. 67FBack

    67 Super Snake Project

    Battery Box Found this battery box on E-Bay
  13. 67FBack

    67 Super Snake Project

    Vent Wings I rebuilt the vent wings. Even after many hours of polishing, it does not remove the pitting. But it is better than it was. New rubber inside, on the front door edge, and new felt lines the window channel. The only special tools need to repair these items is a narrow rivet gun, and a...
  14. 67FBack

    67 Super Snake Project

    Almost Ready for paint Well, the car is almost ready for paint. A few surprises here though. Biggest surprise, the front flares and fender rocker panels cut from the fiberglass fenders and moulded on to steel fenders. Front nose is a bolt on piece now! The upper nose piece was by far...
  15. 67FBack

    67 Super Snake Project

    Rear Speakers I mounted the rear Speakers. Infinity Kappa's 6x9 3ways. I glued a 3/16 board to the back of the divider, cut out the holes, added carpet to the back, and then mounted the speakers.
  16. 67FBack

    67 Super Snake Project

    TKO 900? nice! Is it from MMR? The bell housing fit very tight to the transmission. But I have not bolted it to the engine yet. I will still have to do the alignment procedures. As I understand it, due to engine manufacturers tolerances in regards to dowel pin locations, it can cause a bore...
  17. 67FBack

    67 Super Snake Project

    Console Thanks! The console was $445 through Unique Performance. But I don't think they are selling any more parts, except through vendors. I have not seen it available anywhere else yet.
  18. 67FBack

    67 Super Snake Project

    Stereo Found this little jem for a steal at Shipdog. 3 1/2" screen, DVD, HDD, Navigation, 40 meg HD (16 for nav, 24 for music-pictures etc), CD, Mpeg1, Mpeg2,
  19. 67FBack

    67 Super Snake Project

    Center Console I spent another 6 hours on finishing the console. I decided to put an electrical junction at the front of the console, use quick disconnect plugs for the speakers, power windows, and all electrical connections to ease the installation process. There are quite a few wires...
  20. 67FBack

    67 Super Snake Project

    TKO 600 Got the transmission out for test fitting. I bolted on the Shelby shifter, Lakewood Bell housing and transmission mount. The hydraulic throwout bearing: Built a bracket for the hoses from the the hydraulic throwout bearing: And hoses to the clutch master cyllinder:
Top Bottom
Back
Forums
Menu