Search results

  1. J

    Well, it finally happened, I bought a Chevy!

    Nice SUV. I got a Silverado and will never buy anything but Chevy for a truck. I do love my mustang and will probally keep it till I die, but I would not buy a Ford truck. To each their own.
  2. J

    Glowing headers at idle after 5 minutes?

    Pull the plugs first, and tell us how they look. Does the car smell really rich ? Does it have any detenation ? I would put my money that its running lean.
  3. J

    busted cats

    Well if it has oxygen sensors before and after the cats than you could take them of f, put straight pipe in and get simulators for the post sensor. You could always just take them off, hollow them out and reinstall and see if you get a code for the oxygen sensor and if you do get a simulator.
  4. J

    Have some hot chocolate looking oil in my air oil seperator?

    I am betting your fine. Just from the car sitting.
  5. J

    smog removal and tab/tad help

    I have the same code, to my knowledge it does not affect driveability or performance, only throws the code. I need to make the eliminators.
  6. J

    Door question

    I had a problem with a actuator not fully unlocking, I had to have my key in the door and actually unlock it and pull the door open at the same time to get it to open smoothly. A new actuator obvisouly fixed it.
  7. J

    plugs

    I've had good luck with the 25's, I have heard from a lot of people that Bosch is junk, and our cars dont like the platinums that much.
  8. J

    Removing dowel pins from flywheel?

    I have heard of machine shops putting a rag around them and pulling them out with vice grips, but I would use that as a last resort after the punch method.
  9. J

    Show some interior mods...

    I like the door panel upgrades.
  10. J

    Chairs out of old seats?

    I have a few friends that have done that and put them in their garage.
  11. J

    S197 Seats in a foxbody

    Like said above have the seller take measurements diagonally from hole to hole. Should tell you how far off they are. I'm sure you could use your fox brackets and fab up adapters.
  12. J

    Driveline vibration

    How are your U-joints. Like the others said a aluminum DS is a good investment.
  13. J

    Anyone Here A Cop?

    Your best bet is to go get a degree first in criminal justice and/or psychology. Most depts that I know of require a degree or military experience to even be able to take the entrance exam. If they don't than I would get it anyways, as its a huge part of the promotion process. If your 18 now...
  14. J

    Alternatives to dccontrol e fan controller

    I read about SPAL, being a good company. They are on eBay for $69 I think.
  15. J

    Fitment of SN95 Seatbelts in Fox

    The female end is attached to the 03 seats, I still have the fox male (reels) in the car, which don't retract either. I am willing to spend the hour or two to get it right. I think that next time I run to the local U-Pull it yard that I am going to grab a set of belts and give it a try.
  16. J

    Fitment of SN95 Seatbelts in Fox

    I like the look of the 03 recievers. I guess I will have to do some more research.
  17. J

    Fitment of SN95 Seatbelts in Fox

    I recently put 2003 seats in my Fox, and would like to know if anyone has put SN95, or newer seatbelts into their fox. I would like to use the reciever that is bolted to the 03 seats. I have searched but not found a straight answer.
  18. J

    Car will not get up to operating temperature

    My car only gets to the "L" on normal and puts out decent heat. Like others said the stock guages aren't the most accurate gauges.
  19. J

    wrx or foxbody 5.0???

    What response to you expect on a mustang forum ? Mustang +1
  20. J

    Pulled codes 81,32,67

    Thanks, since the last owner took out most of the emissions stuff, i am going to cap the vaccum line at the manifold for the TAD, and TAB.
Top Bottom
Back
Forums
Menu