Search results

  1. starkie

    DYNO TUNING ??????s

    Thats where I would go. You are close to him, and he is damn good. Starkie
  2. starkie

    Anyone ever remove the rear sterio speker box/ampsms

    Those speakers can be mounted easily, but like you guessed, they are low frequency drivers and powered by the amps. No signal to them without the amps. If you were gonna take em out, I would suggest getting a new radio and speakers everywhere. Then you could simply rewire the system. Starkie
  3. starkie

    Those who know how to install gears

    No. You don't need the shaft until you put in 4.30's or higher. You are good to go. Starkie
  4. starkie

    Has anyone seen a mod where you bypass your airconditioner pulley for more power?

    By routing a shorter belt, if you can manage to do that, will gain you next to nothing. The AC eliminator doesn't free up much if any HP, but you drop 35 pounds of weight by ditching the AC crap. Starkie
  5. starkie

    Driveshaft Loop????????????/

    You could also get the one from UPR. Theirs is sort of a triangle that will also fit around the aluminum driveshaft with ease. I installed the Lakewood loop in a buddies car and it was a tight fit, while the UPR one I put in my car was about a 20 minute easy job. The UPR one is a 2 piece unit...
  6. starkie

    3/8 or 1/2 Extension Bar/Swivel for X-Pipe Install?

    You will have better luck with the 3/8 ones. Starkie
  7. starkie

    mass air ?

    You mean the heat sheild on the FIPK I am assuming. And the answer is no, not without modifying it by cutting out the middle to allow the meter to pass through it. I suggest a Pro M 87 mm MAF. They have the flange just like the stocker that will bolt up, and it is a good meter to use...
  8. starkie

    What size MAF on stock 99 Cobras?

    80mm calibrated for 24 pound injectors. Starkie
  9. starkie

    Ran a [email protected] 3.27 Gears, NA!!! 3476 lbs!!

    Whoops! -1900. Duh on me. Starkie
  10. starkie

    Ran a [email protected] 3.27 Gears, NA!!! 3476 lbs!!

    Ha! Right about then I was watching your race against that Bullitt you have on Video, and saying I gotta start modding my car!!!! :nice: Starkie
  11. starkie

    Ran a [email protected] 3.27 Gears, NA!!! 3476 lbs!!

    My question to you is do you even know what a WATER PUMP PULLEY LOOKS LIKE? :rlaugh: Starkie
  12. starkie

    Ran a [email protected] 3.27 Gears, NA!!! 3476 lbs!!

    Actually about 1900. I was just making an example in my last post. Starkie
  13. starkie

    Ran a [email protected] 3.27 Gears, NA!!! 3476 lbs!!

    Density Altitude is the actual weather conditions for the specific time in feet. For instance. Atco is 50 feet above sea level. If you run at Atco in the summer, with a temp of 90 degrees with 50 percent humidity and a barometric pressure of 29.50 you come up with a DA of 2816 feet above...
  14. starkie

    Can 2v's get 12.5's NA?

    Me, of course....... :nice: Starkie
  15. starkie

    HP/TQ gain from Bullitt intake?

    Depending on what else you have done, the Bullitt intake gains a peak HP of around 6-10. But that doesn't tell the whole story. Where the stock intake drops off, the Bulllitt intake does not. So at higher rpms the Bullitt intake is worth upwards of 20 plus HP. You can feel the difference, on...
  16. starkie

    School me, I needs the clutch info.

    It routes differently, but you will see it is no problem whatsoever. Starkie
  17. starkie

    School me, I needs the clutch info.

    You can still use that cable. It is just shorter. I have the 79-93 cable in my car. Starkie
  18. starkie

    Aftermarket 2v Heads

    You said it in a nutshell. I don't see any offerings with the 3V heads due to show up on the new Mustangs. Starkie
  19. starkie

    Does the k-member need to be dropped to install jba's

    I didn't want to tell you the JBA's weren't worth it over the long tubes, but since you made up your own mind I say RIGHT ON!!! :nice: Starkie
  20. starkie

    School me, I needs the clutch info.

    Your clutch is 10.5. I believe they went to the 11 inch clutch in 99. Your quadrant will work in the Cobra. I would get the McLeod clutch kit. Price is good, and its about the best all around clutch out there right now. Pedal feel is great. Starkie
Top Bottom
Back
Forums
Menu