Search results

  1. ronstang94

    Rear Brakes????

    If you are sticking with the stock calipers you can do the baer 13" rotor kit in the rear. It uses an adapter plate to move the caliper out further (no need to pull the axles.) Its really not that hard to pull the axles though, just make sure you remove the ABS sensors, so you can pull the...
  2. ronstang94

    Nissan CV joints

    I know, not mustang, but I dont want to go sign up for some forum Ill never use again, and someone here probably knows. Why is it important to mark the allignment of the axle, inner race, and ball cage? What happens if they are not assembled in the correct allignment? I marked them with a...
  3. ronstang94

    5.0 radiator swapped into a 3.8?

    Will the radiator out of my 94 5.0 fit in my sisters 98 3.8? She needs a new radiator, I need to get a bigger radiator, and this would be a cool solution. I havent really looked at hers too closely to try to figure out if it will work, just hopin someone will know. Thanks
  4. Imported Item

    Imported Item

    shiney
    • ronstang94
    • Media item
    • Comments: 0
    • Album: My Mustang
  5. Imported Item

    Imported Item

    smoke show
    • ronstang94
    • Media item
    • Comments: 0
    • Album: My Mustang
  6. My Mustang

    My Mustang

  7. ronstang94

    valve covers

    yes the valve covers can swap sides. The bolt pattern and shape is exactly the same foe each
  8. ronstang94

    valve covers

    almost any valve cover meant for non-EFI (older 302s) will have a hole on the left side of each valve cover. So this would put a filler hole at the front of the drivers side valve cover and another filler hole at the rear of the passenger side valve cover. They also have valve covers that dont...
  9. ronstang94

    which rear lower control arms??

    MM adjustables, or if you are going to run coil overs just get the non adjustables
  10. ronstang94

    header advice?

    do yours have the EGR bung?
  11. ronstang94

    valve covers

    you could switch them if the filler neck will be clear of the intake manifold, but i dont think it will be. Im not sure how far the cobra intake goes over the drivers side valve cover. Take some measurements, it might work, but it could put the filler neck in an even worse spot.
  12. ronstang94

    Changing rear diff fluid

    The Friction modifier just is not necesary. The Ford Motor Company states that it is only necesary with the initial oil fill of a new differential. I have heard of people using friction modifier and other people not. Some who have used it have experienced problems. If not using FM causes a...
  13. ronstang94

    Phoenix area guys... I need some help

    still need help? I live on 35th ave and Northern. I have time today and tomorrow. We can work on it at my place or yours. I have plenty of tools, jacks, and all that. Let me know.
  14. ronstang94

    header advice?

    where to buy frpp headers?
  15. ronstang94

    Changing rear diff fluid

    two bottles 80w-90 thats all. NO friction modifier.
  16. ronstang94

    Best cruise speed for mpg?

    I have 2.73 gears and an Aode. I have to get up to 50mph for the transmission to shift, but then I back off to 46mph and lock in the cruise control. The RPMs are just barely over 1000, so that has to be some good gas milage :D
  17. ronstang94

    header advice?

    I already have a bassani mid pipe with some high flow catco cats welded in (banged up the original bassani cats on some speed bumps), so LT are out of the picture because I already have ground clearance issues (lowered). I also have magnaflow catback, hypertech coil, and ford racing wires...
  18. ronstang94

    out of curiousity

    Try not to get your hopes up too high. These cars are not that fast when they are still basically stock. I ran down the track with very similar mods but with an AODE, and only got mid 15's. So, expect low 15's and be really excited to get into the 14's :D . It sucks to be dissapointed, try...
  19. ronstang94

    header advice?

    I want shorty, unequal length headers with EGR but, I can not decide between painted or polished ceramic? I also don't know what brand? For some reason (no reason at all) I don't care for BBK. I dont really like their logo, and I dont want to see that little badge on my headers, but if...
  20. ronstang94

    painting rusty drilled and slotted rotors

    Thanks for all of the replies. This is what im getting from this thread: 1. Most have sprayed the inside and outside of the rotor hats and not had a problem 2. Some have seen that painting the inside and outside of the rotor hats will cause the paint to melt and glue things together (I...
Top Bottom
Back
Forums
Menu