Search results

  1. T

    Braided hose ^%!@%$#

    Yes.. the fiber reinforced packaging tape. It works great, forgot about that.
  2. T

    EFI conversion help!!!

    Youre going to need a TFI distributor, The MSD isnt going to swap. The stock ford TFI(thick film ignition) EFI distributor is very good. Doing an EFI conversion can be alot of screwing around but its VERY rewarding, and If you take your time and build your own harness(everything you need to know...
  3. T

    EFI conversion help!!!

    Unless youre running an all out race car the Ford EEC IV is more than adequate,anything else would be a huge waste of money. Im running a 425HP 331 using a standard A9p processor,90mm Mass air meter from a lightning and a 4 program chip.. Theres ALOT of tuning capablity with the EEC using...
  4. T

    The SN65 project car

    That show has totally ruined my opinion of Boyd. Whod have thought that the street rod king was a really an a-hole dork?
  5. T

    EFI conversion help!!!

    The return line into the filler neck is a hokey setup IMO. Anyone can solder a piece of 3/8 steel line into a sending unit in 10 minutes, I dont know why people are so afraid of it. I suggest you check out www.fordfuelinjection.com. Not trying to discourage you ,but if youve got a factory...
  6. T

    Braided hose ^%!@%$#

    Try using a narrow wrap of electrical tape and leave it on the hose while you slide the fitting over. Pull the tape out once the fitting is started, if you cant pull it out, just trim off whats exposed
  7. T

    New Disk Break Problem! HELP!

    Are you sure its a disc brake M/C? M/C piston diameter plays a major role in pedal feel.. smaller the piston the softer the pedal and power assist amplifies the soft feeling.
  8. T

    Need opinions on aftermarket seats

    reenmachine do you know if those elites can be bought to match factory colors like the Flofits? Ive got red pony seats.. to date Flofits all Ive seen that'll match, and theyre expensive. Id be satisfied with a real close color without the pony decor, I just cant do black.
  9. T

    Does Your Mustang Sit Level?

    Mine is 1/2" higher on the passenger side
  10. T

    Bent Frame??

    Its not uncommon to have the ride height vary on these old mustangs. My car is a suuuper rust free, crash free car and I measured every dimension under the sun and swapped a bunch of parts in an effort to figure out why my passenger side sits 1/2" higher, till I finally listened to some advice...
  11. T

    Alignment Question

    Since you had a bent strut rod have you taken into consieration that the car may have slight accident damage thats causing you grief? It might not be a bad idea to take some chassis measurements.
  12. T

    Anyone using a F-R steer box and Quick steer kit together ?

    Im guessing its not the FR box. I measured and compared my FR box to the oem box that came from my car, there are a few differences in castings but the major dimensions and shaft locations were all the same.
  13. T

    2000 4.6l cobra crate engine swap into 65/66 mustangs?

    And it had a 5.4L not a 4.6..
  14. T

    EFI CONVERSION!!!!?!?

    My cars got a 400+HP 331 EFI, However Its still got the 3.00 gears in it and a 5 speed(3.73's are going in soon) My highway mileage is always 25-26mpg. Its really quite amazing. it gets better mileage than my wifes nissan. I dont drive it much, Ill bet Ive filled the tank 2-3 times in the last...
  15. T

    front disc conversion kits

    check out www.hotrodheaven.com theyve got some big rotor wilwood kits for vintage stangs, some are complete wilwood kits, some are kits theyve put together using wilwood calipers.. Im looking at their 12.19" kit, they sell it for $801.00.
  16. T

    Mustang Plus Carpet Kit Is Junk!

    Ron, great to see you post here. I too have bought from you with nothing but great results, but since you bring up the catalogs I have to chime in with a complaint. I find the catalogs a bit unorganized, I love the color photos and the tech stuff but It drives me banannas that you list the same...
  17. T

    Cobra IRS?

    are you guys talking about dvs restorations? I think the cobra IRS only fits 67 and up. Its too wide for the 65/66
  18. T

    that fix a flat stuff is amazing.

    as long as your not the poor guy who has to make a repair or replace that tire, then its just a mess.
  19. T

    65-6 vs 67 front suspension

    Whats the difference dimensionally between the 65-6 and 67-68 front control arms, are they longer or shorter? Ive got a 66 going together that Id like to widen the track width on in an effort to run late model wheels without spacers. Ive got a 68 9" rear in it and its perfect. Would like to do...
  20. T

    Another T5 Swap

    www.poweredbyford.com $1099 For a new Z spec T-5 free shipping. Tough to beat that price if youre shopping new.
View older results
Top Bottom
Back
Forums
Menu