Search results

  1. T

    Roller rocker came off

    That great:nice::nice:
  2. T

    Need help, 67 pillar pad install

    GOT ANY PICS
  3. T

    want to redo rear seats

    CJPONYPARTS.COM Sells it in pieces or in kit.
  4. T

    1968 289 Mustang - Valve lash?

    :nice:
  5. T

    Custom Throttle Linkage

    Throttling the engine in the driveway does'nt put torque on the engine. You must drive it or brake torque it to get the engine to lift. Remember that ford engines torque up on the drivers side, (the engine will lift on the driver side) With a small hole you might end up with a stuck throttle...
  6. T

    Roller rocker came off

    Even a new engine with have a small amount of oil in the cylinder so a used engine will have more. you need a thin oil film so the ring dont seize up. When you have a cylinder that is not running or one that has the intake valve closed all the time, the oil builds up, this is because the...
  7. T

    1st time questions on replacing the rear main seal.

    Here is a SB Ford Boss 302 1969. Open holes.
  8. T

    Custom Throttle Linkage

    looks good, But, I think the firewall hole need to be larger as to not bind when you snap the throttle.
  9. T

    Roller rocker came off

    I had a rocker come loose on my new 347 that I built, ***** happens even to the best. I had to drive it for 16 miles to get home and pulled the plug as it was wet with oil, I thought the worst, I fixed the rocker lock and started it up, it smoked, I let it idle for about a half hour, same...
  10. T

    Roller rocker came off

    double post
  11. T

    1st time questions on replacing the rear main seal.

    AH, thats wrong. I have several 65 cranks with 28 oz and all of them have the holes open to the oil.
  12. T

    65 brake light switch problem

    ITS the pedal switch Check that you have it mounted correct,, upside down maybe or bushing on wrong side?
  13. T

    Rear Seat Foam

    not much to the foam in rear seat, just go to you local fabric store and pic some out.
  14. T

    Underdash and door light inop!

    fuse
  15. T

    C4 problems

    Ok try this, take off the lever rod to the trany, also remove the neutral start switch. then with a adjustable wrench turn the shift rod and see if it will go into park, dont force it. but do take it all through the gears. If it works then your problem is in the neutral switch. or still in the...
  16. T

    What Fuel Line

    I agree with XOX . 3/8 line will take you well past 400 hp with the correct pump, any larger and you will over do it and then be using adapters to plumb it up which is wrong. The original high performance mustang and shelbys only had 3/8 line and some had only 5/16 line
  17. T

    What Fuel Line

    depending on what inside diameter hose you want to run tells you what size AN fitting to use. Lets say you run a 11/32 inside diameter braided hose then you will need a -6 An fitting. Here are the common sizes of (ID hose) to AN fittings. 7/32 = -4 AN 11/32 = -6 AN 7/16 = -8 AN 9/16 =...
  18. T

    56K warning Lots of pictures! Swapping a '67 Radiator Support into a '66

    NICE WORK 66Runt,,,, Real nice work:nice:
  19. T

    welding in a '67 coupe battery tray, 1 question

    I think you done the right thing to leave the vin number where it is, BUT I also think you made it harder than you have to. I hole you cut will be hard to get a pane to fit correct. I would cut across to the shock tower and down to the frame and take out the whole lower half then you will...
  20. T

    Trunk Floor Rust Protection

    I used Por 15 or you can use any permanant frame paint
Top Bottom
Back
Forums
Menu