Search results

  1. geostang351

    69 Convertible Value?

    How about pictures of the car (body)?
  2. geostang351

    getting to vent area

    Just to give you an idea:
  3. geostang351

    67 stang ride height problem

    If he had a 6 cylinder to begin with, the outer tie rods would be too small for the Granada spindle and there would be considerable "slop and play" at normal driving. Did he replaec the outer tie rods with Granada specific rods? The shelby mod will not drop the ride height any more then 1/4"...
  4. geostang351

    Considering rear end change

    Truck, What size center section are you using? How much is the cost from Currie? Thanks
  5. geostang351

    Pulleys & Brackets for Rev Rotation WP?

    Thanks! Totally different then what I thought you were doing.
  6. geostang351

    Name your mustang?

    My kids (girls) have named it "LOUD CAR"
  7. geostang351

    IS this too much money?

    Looks nice and probabaly a good price except for: The few underside photos show some kind of filler at the rocker rails probably hiding rust. If they are hiding rust there, there may be a cowl rust problem as well. No carpet lifted to show floor boards; no shots inside of trunk at inside of...
  8. geostang351

    Considering rear end change

    Correct!
  9. geostang351

    Pulleys & Brackets for Rev Rotation WP?

    How about an overhead shot of the final install?
  10. geostang351

    67/68 FB rear fender extention molding help

    No, you are correct. On the backside of chrome piece is a track to which the head of a screw can slide back and forth to line up to the mounting holes in the fender extention. You will have to remove the extention to change it. Cutting with a blade through the paint MAY work but be careful.
  11. geostang351

    Starting Problems

    Could have two wires switched?
  12. geostang351

    Pulleys & Brackets for Rev Rotation WP?

    What do you think? http://mustangsunlimited.com/itemdy01.asp?T1=KM1894+01&Category=Heating%2FCooling&subCategory=Belts%2FHoses&CatKey=74-01 http://mustangsunlimited.com/itemdy01.asp?T1=KM1495+01&Category=Heating%2FCooling&subCategory=Belts%2FHoses&CatKey=74-01...
  13. geostang351

    Trying to learn paint and body work.

    NICE JOB! :nice:
  14. geostang351

    PLS Recommend AOD Tranny for 67

    I have an 89' AOD from a Grand Marquis 302 motor hooked up to my 351W.
  15. geostang351

    Pulleys & Brackets for Rev Rotation WP?

    Subscribing. I have the same problem with the Alternator and have to shim it out for my serpintine system. At current I have it shimmed out 3/8" and still throw the belt once in a while. Like to see what you do.
  16. geostang351

    Windshield removal?

    THe trim his held on with snap clips: You'll need to gently slide the trim in a direction away from the windhield to remove the molding. The trim is fragile and probably held in place with seam sealer as well. Once the trim is off, you'll need a utility knife to cut out the exterior of the...
  17. geostang351

    Fuel gauge question.

    The one you are looking for is the last one (73 empty/ 10 full). I got the Autometer gauges in phantom. Here is the link to the site I got them from: http://www.egauges.com/vdo_mult3.asp?Type=Fuel_Level&Series=Phantom&Units=E http://www.egauges.com/default.asp
  18. geostang351

    fuse block

    I have a 68 and the fuse that controled my gauges lights was the small fuse in the middle of the fuse block. It is the only one in he middle surrounded by the other fuses. Notice in 66candy's picture the one I'm refering to.
  19. geostang351

    I need your opinion/advice

    +1
  20. geostang351

    66 GT351

    Oh, when you said "Shoot the car" I thought you meant with paint. :rlaugh: Yeah, New Britain is only 45 minutes. Thanks for the compliment. :nice:
Top Bottom
Back
Forums
Menu