Search results

  1. DemonGT

    MS First start

    Is there a way to use MLV and a histogram like done with the fuel table for the ignition timing?
  2. DemonGT

    MS First start

    Been a bit since i updated. Ended up purchasing a 2021 Mustang so been giving that attention. Made a few small changes to fuel and i had a bad popping on decel that seems fixed after increasing Overrun MAP threshold. Over all it runs good. Before taking a drive i changed idle RPM from 900 to...
  3. DemonGT

    MS First start

    Made some changes to Fuel table and the idle pwm. Also changed the idle to "use engine state". Went on a drive through traffic which wasn't fun but i DID remember to datelog this time. Car seemed to drive ok, it did have a bit of a surging idle at stop lights. I pulled into the garage and...
  4. DemonGT

    MS First start

    Looking at the idle advance settings, if i change it to "use engine state" its set default to 120 degrees and 1 for delay. The idle advance timing is set to 20 in all four boxes shown above load%. Do i need to adjust these boxes?
  5. DemonGT

    MS First start

    I do not plan on using anything other then MS so i will have to purchase the upgraded MLVMS tonight. Should i do the MAT/CLT correction you posted in your other thread? When you get a min i would also be very interested to know more about the EGO stuff as i do not understand any of that.
  6. DemonGT

    MS First start

    First off this is alot of excellent info and should be moved over to your sticky thread "Megasquirt/tuner Studio Tech Thread". For the Fuel table will a few more autotune drives get this closer or do you recommend manual changes also? For the idle, if im sorta understanding this is that...
  7. DemonGT

    MS First start

    That would be great! A explanation on the changes would be most beneficial. Could you elaborate some on "almost hitting targets"?
  8. DemonGT

    MS First start

    Attached is driving log file. I checked the hose and from the vacuum tree to where it passes though the firewall has no kinks, if there is a hose issue its on the cabin side which would require me to remove the kick panel/ecu. I see alot of guys with there ecu's on the passenger side floor and...
  9. DemonGT

    MS First start

    Here is current tune file. It was also suggested by Stinger that i may have a kink in my vac hose going to ECU? He said there is a lag between throttle input and MAP increase in my log?
  10. DemonGT

    MS First start

    Did a few autotune drives and all seems well. One thing iv noticed is it seems to have some hesitation when stabbing the throttle when at idle. Any tips for getting that corrected?
  11. DemonGT

    Blue Ford Rad hoses?

    Tags
  12. DemonGT

    Blue Ford Rad hoses?

    The ones listed for 429.99 they are saying are ford racing hoses and those are blue with a redish orange color on the inside. Mine are all blue. "Police 5.0L 6-piece silicone radiator and heater hose set, functionally correct Ford Racing M-6052-B, we do have individual hoses available too...
  13. DemonGT

    Blue Ford Rad hoses?

    Im using the upper/lower and bypass hose from the kit. There was one other hose in the kit i didnt need and i cut it up to use on my fire wall to cover some unused connections. If there is a demand for these it would be nice to see Ford bring them back.
  14. DemonGT

    Blue Ford Rad hoses?

    Bought a radiator hose kit awhile back and ran across a few small hoses i didnt use since im not running a heater. Been looking on LMR and cant find anything like these? Why are they blue?
  15. DemonGT

    Clutch set up with UPR quadrant

    Not physically move the pedal, just the clutches engagement.
  16. DemonGT

    Clutch set up with UPR quadrant

    Been having some issues with high pedal engagement with my Spec stage 3, was under the car just putting eyes on it to see where my clutch fork was resting. Its a spec stage 3 with a mcleod bellhousing, extended fork and a stock cable. I was worried about the pivot ball also needing shimmed but...
  17. DemonGT

    Megasquirt Digital Dash

    So with the V3 it would connect with canbus but how does the factory wiring for fuel level, high beam etc connect to the DD EFI? ..or is that not finalized yet?
  18. DemonGT

    Clutch set up with UPR quadrant

    I think i need to start from scratch with the adjustment. I think im getting to caught up on how other people have them adjusted.
  19. DemonGT

    Drivetrain Setting Up A New Clutch--Tips Please

    How? Iv been fighting my clutch engagement forever and iv tried just about everything sept messing with the pivot ball. my setup is a Spec stage 3, Mcleod bellhousing, TKO using a extended arm. My clutch engages super high, seems like if i adjust it to lower it then it will not disengage.
  20. DemonGT

    Clutch set up with UPR quadrant

    I feel like the cable maybe to tight? But the firewall adjuster isnt that far out from the firewall? Has anyone else using the UPR triple hook had to use the first hook? I am using a mcleod bellhousing could that make a difference?
Top Bottom
Back
Forums
Menu