Search results

  1. P

    5-lug spare?

    one suggestion... AAA -> free tow. If i get a flat i tow it to a tire shop or my house if they're not open. Save weight in the back /w no jack/spare. Only down side is if you're in a hurry to get someone (job interview or a date...).
  2. P

    94/95 MAF install completed!

    Did you get the one that I purchased? It did not come /w a gasket... it was thin but was not bendable by hand. I used some black rtv on it to make sure it sealed even though it appeard to line up perfectly. Mine was black btw too, in case mabey we got different "ebay" brands.
  3. P

    ordered pulley from FFI never delivered

    I got mine no problem... just ordered the wrong size one. Needed the one you ordered, ended up /w the same size one thats already on there :(
  4. P

    long tube header guys come in

    If you use slip fit I would weld or solder the joint when you put them on. Havn't heard of anyone using them and not havin them leak... sold some a set of bassani because I didn't want to mess with it. I got some ceramic coated bbk long tubes, were not that hard to install. I did remove the...
  5. P

    How to remove front clip?

    Let me know how you get the bolts out of the inside of the fender. I tried to replace my washer resevoir and had a bolt that didnt' want to come loose... it just spun around. The other side of the bolt where the nut would be is behind the amber marker light, and looked to be enclosed...
  6. P

    Teach old 5.0 owner new tricks

    Did the same maf swap, didn't notice any increase in hp but my idle seem seems to be nicer on cold startup.
  7. P

    5spd + Pro5.0 = hard to put in 1st gear?

    Mine (tri-ax) goes in just fine... only problem ever experiences is sometimes it not wanting to go into rev /w out putting it into 1st gear first. (don't have to let clutch out). Mabeyyoure stopps are set to hard? Check the instructions and make sure you didn't set them to far out... only...
  8. P

    94/95 MAF install completed!

    Try searching ebay for "mustang maf adapter" or item #140054338667 Not sure why, but the 3.5" adapter is listed as "v6" mustang.
  9. P

    94/95 MAF install completed!

    Found this on ebay... for $5 plus retarded shipping, was still under $10 and worked great. Fit right on, had to get my own bolts (found laying around). Seemed to fit /w my ebay cold air intake better too... guess because it's longer than the factory maf...
  10. P

    MAC Longtube install pics...does this look correct???

    might want to call them... i bet the auto ones have one that hang lower or something. My bbk manual long tubes hang even. Buts that's bbk, and for a manual
  11. P

    Temp Probe for DCC controler...

    I think i'll give that a shot if it looks seated... I do live in houston, and probalby should have the fan on 100% /w ac and not 50%, which I think the underdrive jumper does as well.
  12. P

    Temp Probe for DCC controler...

    No... i originally put it on the passenger side. I believe the rad flows water in from the top passenger and across to the bottom drivers side. So driver's side bottom. Mine didn't have a cooling problem until it was moved though :( Still havn't checked to make sure I have it seated correctly.
  13. P

    Temp Probe for DCC controler...

    I"ll have to check that out, i did have to drill a small hole and push it through the fan shroud as the shroud was all the way against the driver's side of the rad. Hopefully it's just sticking to far out or something.
  14. P

    Temp Probe for DCC controler...

    Instructions seem to indicate that the probe should be on the bottom of the rad, on the drivers side. I had placed mine on the passengers side. After moving it my car seems to get above 225F now /w a 180F therm... didn't have problems with it overheating before. Where did everyone else...
  15. P

    Mark VIII fan install comments

    I ended up flipping those rubber feet that the rad sits on, and schootching the rad up as close as it would go. I then pushed the a/c brackets back some, routed all the wires that go there in front of the a/c radiator. Then I bent the rad brackets a little to pull the radiator closer... and I...
  16. P

    Mark VIII fan install comments

    I ended up trimming all till 1/2 inch was left between it and the radiator. I read that it shoudln't even be necessary, but seeing as my car was in a front end collision before I bought it I attribute that to my lack of space :( Got it to fit though.
  17. P

    Has anyone seen/used those "Voltage Stabilizers" that a lot of ricers are selling?

    I think there is a top-end (of your trunk lid) kit you can buy... NOS sticker + double stack wing - paint job. Sure to add 30-50 hp depending on size of rims.
  18. P

    Is hatch rattle really this bad?

    got subframes on... it's just more noticable now because everything else stopped rattling. Now people ask me what the rattle is in the back :(
  19. P

    Mark VIII fan install comments

    Pictures Here is a pictures of the install as it sits. overflow tank mounted dcc mounted clearance to water pump snout
  20. P

    Has anyone seen/used those "Voltage Stabilizers" that a lot of ricers are selling?

    Hm... "super earth grounding cable". Nice... and it stores electricity... nice. Looks like they want to sell you a ground cable + capacitor. I guess for $30 and $30 shipping it might be cheaper than replacing your voltage regulator... on a lotus. BUT.. item #190047772533 has a nice graph of...
Top Bottom
Back
Forums
Menu