Search results

  1. S

    Tire size

    255/35/20 is hella small tire for rear of car..he could run a 275/35/20 and it will windo up being about same cross section as a 275/55/15 maybe about .25" wider...I have seen 28x10.50 slicks fit on stock mustang with correct backspacing so a 20"x10" rim with a 275 and lower profile shoudl work...
  2. S

    someone school me on gauges

    most new electric gauges are very accurate. If you go with electric cheap gauges you re gonna get what you paid for. I run a mix of mechanical and electric gauges. i am running the autometer ultralite II and they only offer some of the gauges in electric and its better imo cause the...
  3. S

    Steering column swap?

    I actually swapped the 89 dash and column but you can do the tilt swap without the dash. the opening for the 90+ dash for the c9olumn is larger due to the airbag but you can make the column plastics fit from an 87-89. everything else was the same..I dont know if you can run airbag setup on tilt...
  4. S

    external fuel pump mounting....?

    any one running a sumped tank?
  5. S

    external fuel pump mounting....?

    also mounting a holley blue pump so any inline mopunting solutions woudl be appreciated..thanks..it doesnt seem like there is a lot fo room there...
  6. S

    external fuel pump mounting....?

    Anyone got pics of the way they mounted their external fuel pump on a sumped tank setup? I am installing an aeromotive pump and filter setup and trying to get some ideas how to fab up a plate to mount between bumper support and tank...pics would be appreciated..thanks...
  7. S

    aluminum driveshaft or steel DS with 347?

    I know peeps who run 9s on FRPP aluminum drive shaft with stock u joints. On diff note I know people who have twizzled steel shafts/1350 u joints with 12 second mustangs..I am going to be running aluminum shaft should work fine as stated above...
  8. S

    engine temp guage

    Sense you dont know if gauge/thermostat/or temp sensor are working properly I owuld start by confirming your engine isnt getting to hot...check with one of those infared thermometers if you have one hadny when the gauge says its hot just check temp on block. If its high then I woudl start by...
  9. S

    Solenoid?

    :nice: valid points in so many ways....
  10. S

    Solenoid?

    awwww...k seeign two things referenced above a silanoid and a solenoid..thanks for clearing that up for me....I kno wwhat a solenoid is thought a silanoid was something new...
  11. S

    351C or 460?

    I know a few guys who run clevors....you can check them out on *******.com and corral has a secton with a bunch of guys with clevor combos..Kasse cleveland headed windsor won engine master for under 408 ci...and clevor have placed in top five in engine masters last three or four years...with...
  12. S

    Simple 4 lug question.

    if you run multipiece wheels most tracks require longer studs anyhow...its worth the extra couple of bucks and while you ar ein there pt on some c clip eliminators cause when/if you do break them stock axles you dont want to be the guy whos wheel and axle ran faster then him..seen it a bunch of...
  13. S

    Solenoid?

    whats a silanoid?
  14. S

    351C or 460?

    put a cleveland in it...:) do what ever you want..I like seeing swaps because its diff...I know alot of guys with windsor combos that are super common and dont run right atleast with a swap you got an excuse:eek: jk I would have prob done a windsor based motor but I got a free roller with no...
  15. S

    frame help

    tube chassis the wrecked car....
  16. S

    351C or 460?

    dont listen to them put a Cleveland in it...:)
  17. S

    351C or 460?

    i am in the middle of my swap still ..well about 85% doen now jus tmoney hold ing me back..Ill help you answer as much as I can. BTW Im doing a 351C in a 1990 GT...
  18. S

    GEAR DRIVE? YES OR NO YOUR THOUGHS

    gears arent very expensive..I had gear drive on my last windsor motor it was pete jackson quite and honestly my stock ford power steering pump made more noise. gears are good for accurate cam timing if setup correct the first time but I had a set fail in a mopar motor and it was not nice. The...
  19. S

    Adjustable Pushrod

    http://www.compcams.com/information/Products/Pushrods/ http://www.aa1car.com/library/2004/eb30431.htm
  20. S

    3" Wheel Studs ??

    I got same question but for the rears...? any one know the size needed to run 3" studs with stock drums? I just ordered the ones for the rotors given the part number above...
Top Bottom
Back
Forums
Menu