Search results

  1. S

    Curtis or anderson?

    Who would you go with for a custom grind cam Ed Curtis Or Anderson Ford?
  2. S

    BBK progressive rate springs....

    Anyone have them? How big of a tire can you go with?
  3. S

    1/4 mile worries...

    I in know way fear the gear, but I have a question. I have a 92 lx hatch with 4.30 gears and an aod. Anyone have the same combo? If so how tall of a tire are you using and what are your trap rpm's like?
  4. S

    Aod Question

    I hope you reset the T.V. Cable. The cable that presses into the grommet on the throttle body?
  5. S

    Ignition upgrade

    For a weekend warrior, about 400HP, would a Performance Distributors combo for a 92 suffice or should I go the full msd route?
  6. S

    Timing question

    advance the timing to 14 degree's.
  7. S

    Trick Flow Heads+115k 5.0=?

    If they are under 900$ I think your motor will blow up and you should sell them to me
  8. S

    Timing question

    Run out and buy a timing light. Hook up the light per directions. Remove the spout connector at distributor. loosen distributor hold down bracket. Aim light at harmonic balancer with car running. You will notice small nothes. Turn distributor clock wise till about 14*. tighten down distributor...
  9. S

    1.6 or 1.7 rockers?

    Do a search for anderson ford and call rick's tech line. Give him the cam specs and what you have and he'll give you your answer. He is the cam guru.
  10. S

    30/lb Injectors, Overkill or OK?

    30's are fine. They will also allow for future upgrades. Do yourself a favor, buy an adjustable fuel pressure regulator and gauge. That way you can dile things in a little better.
  11. S

    anyone not running the rubber spring isolators for rear springs?

    Absolutely. The creaking will only stop once you reinstall those isolators. You can look around but i believe BBK has poly urethane ones...hope that helps
  12. S

    kid on a budget - what mods should i do

    I would say: 1. Trans cooler. and make sure you hard pipe the lines, you wouldnt wanna have a hose blow off while runnin' it 2. Shift kit. Trans-go make a pretty good kit and its pretty easy to do yourself if you are mechanical. 3. Gears. no less that 4.10 no more than 4.30 for a street car...
  13. S

    Just some misc. questions

    Im sure that the valve covers will fit....I would say 31 spline axles. Take alook in muscle mustangs and fast fords. Wild rides has 33 splines for 190$. You can usually find them in a package deal with a posi also...hope that helps...
  14. S

    Fiberglass weight savings?

    I am not real sure on weight savings but I would say leave the trunk lid as is. I know it will lighten the car but itll take some weight off of the rear end where you need the weight the most. Unless of course its rusted out like alot of trunk lids are, then by all means replace it. hope that helps
  15. S

    down on power

    I would definatly start off with getting some gears. If its an Auto get either 4.10's or if you are a little more ballsy 4.30's. Then go out and get yourself a fuel pressure regulator and gauge,this way you can dial it in a little better. I would also look to make sure that the mass air sensor...
  16. S

    Lentech aod

    For all you track guru's, I have a 92 hatch with a Lentech street terminator aodw/strip terminator valve body w/electronic OD delete. It has 4.30 gears. I am wondering if on a 26x10.5 inch tire Im going to run out of gear before the traps? I know O/D at the track is a no no hence the delete. But...
  17. S

    best sealed battery?

    Interstate Mega Tron.
  18. S

    Mustangs unlimited upped their prices for Trick Flows

    But if you act fast and call summit, they will matched any advertised price. You have to tell them what magazine you are looking in and what page # and they'll match the 995$ price. As soon as the new mag comes out prices will be updated so take advantage of it now
  19. S

    Intake manifolds

    First decided what kind of HP you want to aim for. Then decide if you want room to open up the intakes a little to add more HP/Torque in the future. Without free flowing heads you probably wont notice much but, if you are aiming for low end the Gt-40 and Cobra will work. If you are looking for a...
  20. S

    Need a set of high flow cats asap

    Where can I get a set of cats for a 92 hatchback, without having to pay an arm and a leg? Does anyone know of a good site to find a set? I got screwed on ebay so I really dont want to buy from there, but is there a better option?
Top Bottom
Back
Forums
Menu