Search results

  1. bdazzgt

    new guy here - too much carb ?

    too much manifold for the street, the Victor JR rpm range is 3500-8000 RPM. IMO kinda high for a daily driver i had a performer and it was great for my 84. I think the carb is ok but too much manifold
  2. bdazzgt

    88 mustang with oem 4-speaker radio...wired for 6 speakers?

    im not 100% sure but i think that if you wire 4ohm speakers in parallel then you drop the ohms to 2 which a lot of amps and cdplayers cant handle. I have mine dash/ door wired in a series connection. i had 2 2ohm subs back in the day that i wired in parallel fried my memphis amp it was not a...
  3. bdazzgt

    Body Molding questions

    the molding is only curled on the door by the back, the rest is fine. I will try the heat then the superglue idea. its ok if i loose some paint because i will just sand it down thanks guys!
  4. bdazzgt

    Body Molding questions

    so i got the motor done for the car, now comes the body work, i fixed all the dents and i started looking at the molding its curled up on the ends on the driver side door, i know this stuff was taped/glued on from the factory, if i take this off will it be salvageable? and what are you supposed...
  5. bdazzgt

    Car just Randomly dies with new setup

    @.50 218*/226*.512 lift 114 lsa and in neutral its around 750-800 its the factory tach with no surge, idles just fine. i took my cousin around the block, it runs great but after some runs to 5k in first, second and third gear went to stop at a stop sign and it died :nonono: i thought i had this...
  6. bdazzgt

    Car just Randomly dies with new setup

    yes it does it when i am downshifting, it seems better i drove it to target to get christmas presents and it ran good didnt die at all. with that being said at some certain points it seemed like it didnt want to idle at the stoplight again. if i downshift and slowly coast to second gear around...
  7. bdazzgt

    Car just Randomly dies with new setup

    i hope it fixes it, the idle is great now i did the whole base setting the tps they are both set correctly now. i thought that some mustangs dont even run the VSS?
  8. bdazzgt

    Car just Randomly dies with new setup

    yes i changed it to a bbk 70mm,with the egr spacer, and i put a 190lph pump in at the same time as the motor. I used the nifty search button found how to set the base idle and readjusted the tps, it was around .75v, would that of mattered? i put all new vacuum lines and fittings, new gaskets and...
  9. bdazzgt

    Car just Randomly dies with new setup

    i will go follow the idle setting checklist again before i go ripping out the gas tank, i just dont want to spend 150 on a new tank. Would it do it all the time if it wasnt correct though? thanks for the help guys
  10. bdazzgt

    Car just Randomly dies with new setup

    yes the idle has been set, around 850 and idles great it just randomly dies when turning or decelerating, also jrichker how do i know when the baffle has been properly placed? and how much jb weld do i need to use?
  11. bdazzgt

    Car just Randomly dies with new setup

    is there any glue expoxy that will work in the gas tank? this could explain my dying on deceleration without downshifting and randomly choking the motor out
  12. bdazzgt

    Car just Randomly dies with new setup

    so my baffle is loose....is this causing my problems? what is the next step can this be welded, bracket fixed ect? btw Jrichker you are the man
  13. bdazzgt

    Car just Randomly dies with new setup

    I just rebuilt my motor with a new H/C/I trickflow junk, it runs great and idles fine but when i go to stop at a stoplight about 75% of the time it dies like someone cut the fuel off. The codes from the cpu are all just the EGR that was removed. I put a new 190lph fuel pump, and a newer filter...
  14. bdazzgt

    finally my first build thread...

    trickflow advertises 350hp, im assuming thats at the flywheel with no accessories, but thats with a completely stock shortblock and their TFS1 cam
  15. bdazzgt

    finally my first build thread...

    Its basically the trickflow kit, i got the heads with new comp double bee spring upgrade, 1.6rr, intake, 24lb injectors, 70mm throttle body and egr spacer, new injector rails, a 8.8 rearend with 4:10's that isnt installed yet and a short block that i sold. i got all the parts for 1600. i wish i...
  16. bdazzgt

    finally my first build thread...

    i decided to redo my door panels, they look decent for less than $30
  17. bdazzgt

    finally my first build thread...

    The motor is finally out....im trying to in some kind of order NEW PARTS WOOT:nice: I moved in the process of getting new parts and pulling motor and now i have a 2 car garage after cleaning up my shortblock
  18. bdazzgt

    finally my first build thread...

    So i finally got my motor back together and the mustang where i can drive it for the first time in 2 years, so i figured i would take pictures and make a half a$$ build thread. First off i am not a professional rod builder so dont be too critical and i am on a strict budget so please enjoy. ps...
  19. bdazzgt

    Windshield Wiper electrical Problems

    so i have an extra plug on my harness does a mustang wiper motor have 3?
  20. bdazzgt

    Windshield Wiper electrical Problems

    so the windshield motor i have doesnt have a connection for the black/pink-black connector is this what causes the wipers to park ect? i think i am reading this diagram correctly. the motor is off like a 91 bronco after i ran the part number is this my problem all along, plus the delay housing...
Top Bottom
Back
Forums
Menu