Search results

  1. JOEGTS

    skinnies question?????

    Yes as long as you use a good tire other than the tire that came with the spare. A spacer has to be used or grind thebar from the padholder or both. I cut my bar comepletely off and had to use an 1/8" spacer using Center Line Telstars.
  2. JOEGTS

    CAR WON'T RUN AFTER HCI

    Thanks I appreciate it and I'll keep posting on the progress.
  3. JOEGTS

    CAR WON'T RUN AFTER HCI

    I pulled the Hypertech chip out and the car will idle somewhat, but pops like the timing is off. I tried to start it with the Spout pulled and it won't start. I will try to set the timing again when i get a chance. I was told that Iron GT40 heads use Autoliye764's?:shrug:
  4. JOEGTS

    CAR WON'T RUN AFTER HCI

    I tried to adjust the idle and it still didn,t work. I didn't know I could just pull the Hypertech chip out and it returns it to the stock settings. I'll try it today if I get a chance.
  5. JOEGTS

    CAR WON'T RUN AFTER HCI

    I don't have a stock chip to try in the ECU.:shrug: I called and ordered a chip from JMS. Hopefully in a week I'll be able to drive my car again.
  6. JOEGTS

    CAR WON'T RUN AFTER HCI

    This weekend I did my HCI swap. I got the car running yesterday afternoon and it ran for a good 15 minutes until I shut it off to get the air pocket out of the coolant system. After getting that worked out I started the car again and it would surge up and down and then die. I installed a Trick...
  7. JOEGTS

    You will never believe this....or maybe

    I have never heard of JMS. Do you have the phone number or the website adress?
  8. JOEGTS

    Anyone seen this before??

    Its not that uncommon with aluminum heads. Supposedly its caused by excessive heat.:(
  9. JOEGTS

    SEALANT ON HEADBOLTS

    Thank you everyone for your help. The reason I asked was I did a search and came up with four different answers. From what I see some people use different torque values for different heads ( aluminum or iron ) and for stock head bolts versus ARP.
  10. JOEGTS

    SEALANT ON HEADBOLTS

    What is the correct torque? I am using iron gt40 heads with ARP head bolts. Thanks.
  11. JOEGTS

    SEALANT ON HEADBOLTS

    I am doing my HCI this weekend and I am wondering if I have to put some sort of sealant on the outside headbolts?
  12. JOEGTS

    VC clearance question

    From what I have read on here the 1.6rr will only fit under the fox covers. Cobras came with 1.7rr which will fit under the 94-95 valve covers.
  13. JOEGTS

    Steeda #19 cam and Crane Cobra Roller Rockers?

    If you do a search you will find quite a bit of info on the Steeda19. Thats the cam I decided to go with. I am installing mine this weekend with the stock rockers.
  14. JOEGTS

    o2 sensors

    I replaced mine witt new ones from Ford, they were around $120.00 for both.
  15. JOEGTS

    What backspacing i need with aftermarket 15x8 wheels

    I am to computer challenged to post them.:shrug:
  16. JOEGTS

    Remove Quad shocks?

    I just recently installed Ford racing uppers and Steeda lowers with Lakewood shocks. My question is should I remove the Quad shocks and rear sway bar. I am not into hitting the curves hard (especially since I run skinnies up front) I just mainly don't want wheel hop.
  17. JOEGTS

    What backspacing i need with aftermarket 15x8 wheels

    I have 15x8 with 5 1/2 backspacing and 275/50/15 drag radials. If i had it to do all over again I would have went with 15x10 with 6 1/5 inch backspacing, they look better.
  18. JOEGTS

    Rear End Noise...did research still need help

    What is the dogbone?:shrug:
  19. JOEGTS

    Rear End Noise...did research still need help

    I have the exact same problem. I installed the Ford racing uppers, Steeda lowers and Lakewood shocks. My noise mainly occurs when I am decellerating in gear. I took my cover off and my gears are making contact accross the entire tooth front and back. I believe I need to take some clearence...
  20. JOEGTS

    Sloppy Trac Lok Unit

    Its deffinetely something inside the diff.:shrug:
Top Bottom
Back
Forums
Menu