Search results

  1. NO_RICE

    New to Phoenix area

    Yeah I live in Mesa and I work in Avondale :bang: Im trying to find another job, but until then I have to make that drive every day.
  2. NO_RICE

    New to Phoenix area

    I am new to the valley, moved here a couple of months ago from Tucson, just wondering what you guys do on your spare time around here.
  3. NO_RICE

    Paint - Tucson Body Shop

    I have taken my car to photo finish, and they do a really good job, but they are expensive. I have also heard than Dan's paint and body does good work.
  4. NO_RICE

    Gap between fender and door!..??

    I had the same problem, there is a bolt at the bottom of the fender, I had a shim in there, once I took it out it lined up much better. I think that is caused by people jacking up the car under that fender. good luck.
  5. NO_RICE

    Cheap ways for more power

    7k rpm on the stock tach is not really 7k. factory rev limiter is at 6125. I have missed a shift and buried the tach needle, it hurts to watch. :notnice: but I would suggest higher octane, and up the timing clean the air filter, new fuel filter. adjust tps voltage. That is about all I can...
  6. NO_RICE

    My A/C barely blows air? Help!!

    mine doesn't blow very hard on 1,2 or 3 but strong on 4, I think that is just the way it came from the factory.
  7. NO_RICE

    window motor help

    My passenger window rolls up really slowly, does anyone make a rebuild kit for the motor. If it needs to be replaced, where is the cheapest place to get a new one.
  8. NO_RICE

    Can i install a push button start?

    Iwashmycar, no that is not right, if you wire it up that way your are still going to have to turn the key, but at the same time you are going to have to push the button. Im sure you can figure it out if you think about it.
  9. NO_RICE

    Will this supercharger work?

    I wouldn't waste your time, if it is even posible to fabricate something for your car, you are not going to be able to fit it under the hood, and I doubt that it is an good condition.
  10. NO_RICE

    Window Tint

    use soap and water to put the tint on the outside of the car, then use a squeegee <- (I fugged up the spelling) to get all the water out from under it, at the same time you need to use a heat gun to shrink it to the curve, don't expect to get it right on your first, or second try. cut it to the...
  11. NO_RICE

    What's wrong with my distributor??

    did you remember to take the jumper out so that the timing is not advanced?
  12. NO_RICE

    3 1/2 months of hell only to get worse

    sounds like you have a bad vacuum leak
  13. NO_RICE

    DO MUCH PAINTING??

    I think that it is funny, scotty says he can tell you anything you need to know, but he never replied to the thread again. I am a profectionist so I think that painting is probably one of those things best left to the professionals, at least in my case. I also live in a town that is extremely...
  14. NO_RICE

    Ford racing motor install

    I just wouldn't want to get a crate motor tear into it to change pistons, when one of the main reasons that I would buy it would be to not have to assemble everything.
  15. NO_RICE

    Need exhaust advice... want to change current setup.

    If you don't need cats don't put them on, the cat h/x pipes are about three times as expensive.
  16. NO_RICE

    1995 302 install into 1990 body...

    It is basically the same motor except for the upper intake, I have never seen the 94-95 style intake in a fox, but I am sure it would work.
  17. NO_RICE

    DO MUCH PAINTING??

    I looked into painting my car myself, but by the time I got all the equipment (a sander, compressor, couple paint guns, body hammers, dollys, etc) it would have cost like over $1000, I like to do everything myself, but it just doesn't seem practical.
  18. NO_RICE

    Ford racing motor install

    Im just waiting for one more paycheck :D, anyway I remembered why I didn't want the FMS crate motor, it has hypereutectic pistons, and it doesn't come with any type of warranty (which is really not that big of a deal).
  19. NO_RICE

    Ford racing motor install

    I was thinking the same thing, if it puts out as much power as it says, it seems like a good deal. A good shortblock with a set of aluminum heads runs significantly more than $3k and you still have to put it together yourself.
  20. NO_RICE

    Saleen ground effects

    you are going to need about $600 worth of LX trim parts, I have a saleen kit that I can't use sitting under my bed collect dust because of this.
Top Bottom
Back
Forums
Menu