Search results

  1. TIMMY2734

    How do I set the pinion angle ???..SSM bars install

    Are they uppers or lowers? If they are uppers, go to baselinesuspensions.com Heres a good thread as well, but Kevin explains it very well on his site. If they are lowers, well ya need some adjustable uppers.
  2. TIMMY2734

    What Is This

    its for your smog pump. If your not going to run it, just crimp it or cap it shut.
  3. TIMMY2734

    Anti-Roll Bar

    The anti roll bar connects to the body via 2 links. Some use bushing and some use bearings. They will make you hook harder and go straight. The one drawback is that they really arent meant for a car that sees alot of street use. You can drive it on the street, but you have to be very careful...
  4. TIMMY2734

    TKO questions and tko clutch questions

    Id rather have it known that what im looking to do MAY NOT work . If everyone says that a certain something will work and it turns out it doesnt, how pissed off would you be. Be honest now...... My driveshaft was fine. Just swapped the yoke. My only qusetion or gripe is that because tremec...
  5. TIMMY2734

    TKO questions and tko clutch questions

    i got it from one of the online vendors. From all of the info ive read, the Mcleod didnt need to be indexed. Guess ill find out the hard way......... Its a TKO, the regular one. I dremeled my crossmemeber and its fine. Gonna get it welded later on. Steeda's website has a list of what to use...
  6. TIMMY2734

    TKO questions and tko clutch questions

    Ive got the Mcleod dual friction or whatever the hell its called. Wasnt expensive at all. I started thursday and had the motor, tranny and k member out by myself.. had the tubular k member and a-arms bolted up as well. Friday and sat, me and my friend went kinda slow, but its ll pretty much...
  7. TIMMY2734

    How much did you pay for port work?

    read and then call... http://bbs.hardcore50.com/vbulletin/showthread.php?t=19459
  8. TIMMY2734

    How do I adjust my rocker arms

    If they are stud mount use these instructions. Simple as pie Compliments of ED C of FTI HYDRAULIC LIFTER/VALVE ADJUSTMENT PROCEDURE 1. Remove the valve covers, and pick a cylinder you are going to set the pre-load on. Only do one cylinder at a time. 2. Rotate the engine in its normal...
  9. TIMMY2734

    Best way to install battery in hatch?????

    yes it will, but i suppose you could wire it to the battery if you wanted to. Easiest spot is right behind the plate. Tons of room to put it there. No pics, too tired to go out now.
  10. TIMMY2734

    TKO questions and tko clutch questions

    Put my motor and trannyin today. Ive got a Mcleod clutch and blowcan, so ill let you know how it feels. Crossmember was fine once i took the grinder to it. Driveshaft goes in tomorrow. Is ERIC building your motor? If he is, id have the clutch and pressure plate and balancer as well shipped...
  11. TIMMY2734

    Will these AFP regulators fit stock rail/setup?

    I had to use a spacer with my aeromotive. The kirban is just about the same size as stock and is a better piece. Its rebuildable and isnt notorious for leaking at all.
  12. TIMMY2734

    would putting allitle hard block in my block be bad?

    If you are redoing the rotating assembly, it really wouldnt hurt much. But if you want to do it in what you currently have, i wouldnt waste my time..
  13. TIMMY2734

    Budget 7500 RPM 302

    It wont be cheap.... really no way around it. -Your going to need top spend some money on a lightweight piston. Wouldnt trust a heavy trw slug. -I dont know if thumpers head will rev it as high as you ask. -Seeing as you want it for autoX, id imagine youd destroy the block in no time...
  14. TIMMY2734

    HELP Bent pushrods why?

    Either way, he has a problem..... Put a band aid on it now, or do what needs to be done so it doesnt happen again.
  15. TIMMY2734

    Header to Mid-pipe Gaskets???

    Stock ball and socket, no. 3 bolt flange, yes
  16. TIMMY2734

    Boxed Upper Control Arms

    You could probably weld a nut the the control arm or figure something out to make it work.
  17. TIMMY2734

    Boxed Upper Control Arms

    Weld them up. The price sounds great and its a win win situation. The worst that wil possibly happen is they feel the same...as stock. But no money lost, no harm done. For anyone who knows Kevin Slaby of baseline suspensions, he cut consistent 1.6 60s with stock boxed arms ....
  18. TIMMY2734

    HELP Bent pushrods why?

    Im with retro on this one. Youve got something binding. What is the part number of teh springs that you bought? Doesnt need hardened pushrods either. They are to be used with guideplates so that they do not wear out.
  19. TIMMY2734

    Got rid of my skinnies and i couldn't be happier.

    Dartman, who makes those headers? Ive never seen a collector like that
  20. TIMMY2734

    Why dont people use Tremecs with 429/460's?

    They do use sticks... Lakewood Bellhousing Part #15220 You can also bolt a richmond 6 speed to it with a little bit of work
Top Bottom
Back
Forums
Menu