Search results

  1. Trublu01

    will cams help my car

    Do all the bolt-ons first. then build your rear for slicks ($1K) then worry about cams and springs.
  2. Trublu01

    Rear Spring Airbags

    It's Jeremy, and I bet if I ride over there tomorrow, I could pick 1 or a set up.
  3. Trublu01

    Rear Spring Airbags

    You really only need one on the passanger side. UPR sells them. Not on their website though (I think) just call them.
  4. Trublu01

    Romeo or Windsor or both?

    There are alot of folks on modulardepot, who have cams, you'll get a real answer there if that tool works like some say. There is no doubt that cam chane and headswap for that matter can be done with motor in car, but easier if out.
  5. Trublu01

    UPR Products

    The fit and finish of UPR's Chromoly K-member is superb. They use QA1 springs for their coilovers. I've installed 2
  6. Trublu01

    Throw Out Bearing Question?

    It's a factory "reset" adjustment
  7. Trublu01

    UPR Products

    In this day and age, who doesn't copy who?
  8. Trublu01

    Superchargers gettin put on right now.. who will I beat?

    HP and TQ don't mean squat if you can't put it down to the ground!
  9. Trublu01

    Good Bolt in SFC's for a 99?

    They are all good as long as they are welded in.
  10. Trublu01

    Romeo or Windsor or both?

    Better add 2 or three BBQ's! Cams is a 6-8 hour job, unless you've done it a few times or the motor is out of the car.
  11. Trublu01

    Got my MRT H-Pipe, Should I Install or Exh. Shop?

    Spray with WD40 and let them sit for a while. It's harder than it looks. **EDIT** OOOPS, I meant easier than it looks!
  12. Trublu01

    How to remove rear seat

    There are two brackets that hold the lower seat cushion in place, right along the front of the cushion. They have tabs right at the front of the bracket that you should be able to push in with a screwdriver. That will release the lower cushion, and you'll be able to pull it out. The upper...
  13. Trublu01

    Problem: loose/sloppy IRS Rear end. Solution: rebuild or replace (posi)

    EATON!
  14. Trublu01

    UPR Products

    Another supporter/user of UPR. They are local to me and never have a problem with service. The Grinch dip**** is just that, a dip****.
  15. Trublu01

    H pipe or prochamber?

    H or X
  16. Trublu01

    Got my MRT H-Pipe, Should I Install or Exh. Shop?

    About 18" in extensions and a swivel
  17. Trublu01

    Romeo or Windsor or both?

    There is a W stamped above the oil pan on the driverside of Windsor blocks, usually the head has a sticker on it that also says Windsor. After being on this board for 3 year, I have never seen a windsor motor in a 2001 Mustang GT. So I doubt you have one. Even cars built in 2000, like mine...
  18. Trublu01

    Looking to order some LCA's...recommendations

    UPR, Tubular, Chromoly UCA/LCA's!
  19. Trublu01

    What will a 70MM THROTTLE BODY give me?

    Huh! I gotz mad power yo from a 100mm T/B, My ****at gained 60hp at the wheelz yo! Who needz tq? Don't waste your money, unless you have done every other bolt-on available.
  20. Trublu01

    Throw Out Bearing Question?

    Umm, there is not stock adjustment at the firewall. Pull out your clutch pedal with your hand then push it back in with your foot.
Top Bottom
Back
Forums
Menu