Search results

  1. DTMach1

    Will CAI lean or richen

    let us see here...you are asking if something that is supposed to increase AIR flow will lean a car or richen a car? and the answer is...LEAN but just a tad...usually if it is your first mod it will lean it out just enough to pick up a few horses. these cars come from the factory with a...
  2. DTMach1

    New NMRA Factory Stock Record

    you see what happens when people find out you're getting rid of the Cobra?!?!
  3. DTMach1

    Bug Remover

    wasn't there a similar post yesterdaY??? Use a claybar, that will remove the little buggers just fine
  4. DTMach1

    I hate RAM

    I hate ROM
  5. DTMach1

    Belt size for U/D pullies?

    it wont hurt anything to give it a spray to isolate the problem...I had a belt squeal on '97Gt and sprayed it with wd40 and had no issues...I found out the STeeda pulleys had stretched the belt (the car 74K miles at that point) so I replaced it with a gatorback and never had a squeal again(sold...
  6. DTMach1

    Canyon Carving suspension setup

    here, go to this site... http://www.mach1review.com/BlackSheepCanyonCarversSpecialHandlingPackage.html
  7. DTMach1

    New NMRA Factory Stock Record

    damn, and I had just met Bob Cosby not more than a week ago(he had the record) Don't worry...Jeff Schmell will get a new record next year...
  8. DTMach1

    Belt size for U/D pullies?

    stock size belt will do fine...however, if you start to hear some squeeling...spray some wd40 on the belt...if the squeeling goes away buy a goodyear gatorback...
  9. DTMach1

    Long tubes with cats

    BBK, SLP, Hooker, just to name a few...
  10. DTMach1

    Rich, Lean...Who knows?

    I'd guess you're around a safe 12.7...a little on the rich side...but safe... I think with all the intake work, plus the LT's you went from lean to rich to safe.
  11. DTMach1

    My cat is rattling - Question for catted MRT H-pipe owners

    usually the warranty card guarantees the cats for 50k miles or something close to that. It also states that you changed your old cats out due to a faulty cat. or you're car is past 75k miles.
  12. DTMach1

    [B]What is Claybarring and How?[/B]

    how is plain water bad??? it's only there as a lubricant. Clay bars don't scratch paint so the closer you are to the clear-cote the better. Plain water works better than the quick detailer lubricant that comes with the kit.
  13. DTMach1

    Track Times..why so slow?

    here is a hint...don't use "Z" where an "S" is appropriate. That will lower your E.T.'s by a considerable amount...
  14. DTMach1

    1st time @ track 02 gt vs. 04 Mach

    i guess this is ugly too?
  15. DTMach1

    1st time @ track 02 gt vs. 04 Mach

    THIS is ugly???
  16. DTMach1

    [B]What is Claybarring and How?[/B]

    ummm you have two choices when it comes to using a claybar...one is to use the stuff that comes with it...or just plain water. If you look mother's has a kit that comes with a bar and a spray. just spray and then go over the car in a back and forth motion. Do not spray too much or you'll...
  17. DTMach1

    1st time @ track 02 gt vs. 04 Mach

    It's all driver and track dude...it can and has been accomplished...if you look over at a couple of the mach related boards, a good driver is capable of making their mach run 13.1 stock. In fact, the founder of one of the mach boards is in the 12's with just a tune and CAI...and yes on radials.
  18. DTMach1

    Track MPH

    spinning can be a factor as stated before...I've spun first through the 60ft and when I finally got traction I trapped at 14.4 @ 104mph...If I hadn't spun like that, it would've been an mid 13 second pass that time...
  19. DTMach1

    My GT won't run

    IAC or a fuel filter
  20. DTMach1

    1st time @ track 02 gt vs. 04 Mach

    you must not go to a track very often, or know very little about drag racing... I've seen cars with well over 400hp to the wheels not break 14's...why??? it's all in how they put that power to the ground!!! Mach's are set up from the factory to drag race, plain and simple...even in stock...
Top Bottom
Back
Forums
Menu