Search results

  1. StonePony

    manual to 4r70w guys in here please

    That shifter doesnt work - period - and that is why its not for sale yet.
  2. StonePony

    2008 GT Auto Supercharged. Power?

    Stay away from that TCI tranny. I had my tranny die way back at about 445 RWHP. I have the Level 10 Stage III and it has held up to 523 RWHP fine for 20 months,and my car launches very hard.
  3. StonePony

    Throttle body spacers?

    waste
  4. StonePony

    Lowering with smaller diameter tires

    Yes you could lower it and go for the Mexican look.
  5. StonePony

    cheapest place to buy MT ET Street Radials

    Im waiting for the 305/35/18 MT ET Drag radials they are about 26.4" and will have almost 12" width. The 305/45/18 is taller which is okay but too skinny.
  6. StonePony

    Drive-Shaft Loop

    I have the GMS kit. It is very easy to install. It mounts using the existing shield studs and is in two pieces so there is no need to remove the driveshaft.
  7. StonePony

    Tire Pressure Gauge?

    Moroso Drag radial gauge
  8. StonePony

    Drive-Shaft Loop

    Dont believe for a minute that if you blow a rear u-joint that the driveshaft will just drag on the ground. I dont know where Darkfire GT came up with that idea, but let me tell you what happened to my car when the rear u-joint blew and I had no loop: 1967 GTO running through the gears at the...
  9. StonePony

    ET Streets on 17" wheels

    I have been running ET Streets on the stock rims for two years. The bias-ply is a wrinkle wall slick with two treads so they are very good for the track.
  10. StonePony

    wiring a boost gauge and a/f ratio gauge

    It is easiest to run you own power wire from the fuse panel using an add-a-fuse.
  11. StonePony

    need tranny

    Lentech sells a 4r70w with a stand-alone computer or with no computer and a full-manual valve body, driveshaft and etc for 6500. Len's stuff is second to none. I have one of his AODs in my fox body.
  12. StonePony

    ET Streets

    I use the M/T ET Street 26 x 11.5 x 17 (3743) bias ply on stock rims at the track. It would not be a good choice for the street.
  13. StonePony

    boost gauges

    If you are determined you can run the wires and/or vacuum line through the firewall and under the dash. Then you can force fully squeeze them through the seam of the defrost vent/dash pad and out throuigh the defrost vent. No holes drilled. I have three gauges wired this way in my dash pod.
  14. StonePony

    Cam shaft for 07 4.6L 3V Mustang GT

    Okay well not everybody gets that result. In fact most of the results I have seen were approximately a 14-17 gain. (Those were from Brent too)
  15. StonePony

    Cam shaft for 07 4.6L 3V Mustang GT

    I guess you didnt look very hard. Comp Cams and Crane Cams sell 3-valve cams. So does Blow-by-Racing and Sutton will have cams soon. There are lots out there. The problem is they give very small gains because the stock cams are pretty darn good. Oh and they are expensive too. the NSR (no...
  16. StonePony

    What Brake Fluid Should I Use?

    Castrol SRF (DOT4) Best thing out there but expensive. Dont buy 5.1 it has to be changed all the time
  17. StonePony

    Premium Fuel

    Just pony up and pay for the octane.
  18. StonePony

    10 sec club

    It is a stroker motor. It is Jim Jr. at JDM
  19. StonePony

    10 sec club

    NOBODY anywhere is running 10s in a S197 witha N/A 4.6
  20. StonePony

    Are 4v heads from the 03/04 Mach 1 compatible as a swap for our 3v heads ?

    You would have to change heads, timing cover, timing chains & gears, water pump,intake manifold and TB. Then you would need to be a magician to re-tune your PCM to have no variable valve timing, because you now would be running a four cam setup. There would be other issues with changing radiator...
Top Bottom
Back
Forums
Menu