Search results

  1. S

    Anybddy running "Maxspeed" lowering springs?

    I just ordered some FRPP springs and was wondering what is so great about Eibach? What are the spring rates and how much will it drop a car. The FRPP's say that it will drop 1.2" in the front and ~3/4-1" in the rear. I figure that if I pull the rubbers it should give about another 1/2"
  2. S

    Anyone with 4.10's wish they have gone w/3.73's

    Love the 4.10's. Dont fear the gear!
  3. S

    no MIL Elims on an o/r pipe... safe?

    How do you do this? I have been running mine with the SES light on for about a year now, but it would be nice to have it turned off without having to worry about dealing with the MIL eliminators.
  4. S

    4.10's in a 2000 GT?

    I would definietly go with the 4.10's. I installed them in my car a while back and love them. There is not much difference between the 3.73's and 4.10's as far as highway driving goes, at 70mph about 200rpm difference.
  5. S

    Hypertech Programmer Questions

    I got my Hypertech Programmer today and hooked it up to tune my car, firm up the shifts and re-calibrate the speedometer for the 4.10 gear in my automatic GT. I did all of this and followed the instructions step-by-step and I see no change whatsoever. The speedometer is still wrong and nothing...
  6. S

    Alignment Question

    If this is where the steering wheel stays while the car in going straight and there is no pull until you brake, then someone has set your toe-in on the front end and did not look to see if they had the steering wheel straight. Go talk to the guy who lined it up for you.
  7. S

    Steering wheel shaking...

    If it is the steering wheel that is shaking then it would have to be in the front end of the car. Drive shaft problems would cause you to feel the vibration in your seat. I would recommend rotating the tires from front to back to see if the vibration follows the tires. If it is not the...
  8. S

    Alignment Question

    I used to do alignments and this may be because whoever aligned it did not make sure the steering wheel was straight when they set the toe. Does the car pull to one side or the other, or does the wheel just stay turned while the car is going straight?
  9. S

    What's going on? Missing parts? Gear help!

    The orange thing is your new pinion nut and it should come with all motor sport gears. t is orange from thread lock and sealant. The plastic bag is the pinion shims, and the brown paper should have a crush sleeve inside of it. I hope you fellas know what your doing with those parts...
  10. S

    New Mustang GT 96 Owner Please Help

    4.10 gears will be the best bang for your buck
  11. S

    Rev limiter: Did I hurt the stang?

    To hell with it. My engine has 70K miles on it and I have hit my rev limiter too many times to count, when the auto tranny doesn't shift fast enough when I am manually shifting it, or when the tires break loose in first or second gear it tends to jump in rpms too fast. The limiter is there for...
  12. S

    Hypertech Power Programmer

    According to hypertech's website you can get one and about any Advanced Auto Parts store for $309.
  13. S

    Question about gears

    I would say that your car probably has 3.08 or 3.27 gears in it. I'm not real sure. What I would do if I was taking it to a shop and saying here install this, is to get the FRPP ring and pinion, and a FRPP install kit that comes with all of the bearings, shims, seals, crush sleeve and gaskets...
  14. S

    Exhaust Leak Need Help

    :D If it is on the passenger side of the car then there is an exhaust gasket there, it is hard to find excepts for from the dealership. If you have stock manifolds and pipes then these bolts should not be missing because they are studs from the manifolds that have nuts on the other side...
  15. S

    3:73's, 3:90's or 4:10's

    There isn't much an rpm difference between 3.73's and 4.10's to worry about. Only a couple of hundred difference between the two at 70mph. Go with the 4.10's
  16. S

    Where to start

    I defininetly recommend changing the gear to a 4.10. In my opinion this is the best bang for your buck. :nice:
  17. S

    My final review of my 4.10's!

    Its good to hear your positive review of 4.10's. I am installing mine this weekend and was worried about problems with traction. :nice:
  18. S

    Re-Flash of Chips for Speedo?

    I talked to a guy at our local dealership and he said that it may be possible on some cars, but he will have to look at the car to see. I'm not sure if will do it off the record. The gear is going in next weekend so I will have to wait and see.
  19. S

    How to remove entire dash?

    Plasma Cutter = Get er well done
  20. S

    Re-Flash of Chips for Speedo?

    Who is Cobrakiller and can he re-flash a stock chip to for 4.10 gears? :shrug: If so how can I get into contact with him?
Top Bottom
Back
Forums
Menu