Search results

  1. C

    Mustang dies at Highway speeds!!

    I've seem this problem sometimes being caused by cold air kits. I'd remove it and re-install the stock setup and see if it helps.
  2. C

    AODE NOT STRONG ENOUGH!!!

    They've made SFI bellhousings to bolt C4's to a 4.6 for awhile now. I know of a few people that have them on there drag cars..Dave Guy who runs his car with a Cobra engine car in Renegade, Alian who has a YSI on his 96 GT has one. You can go to Performance Automatic and they have them listed...
  3. C

    Help with SVO rear end for 90 gt

    Ya, I put a rear end out of an 86 SVO in my 91LX. It is an 7.5" rear end with limited slip diff, 3.73's and 5 lug. You can look at the diff cover and tell that it's not an 8.8.
  4. C

    dual focus pumps question

    I used the one off of modularfords in the reference section. I think I used a 10 gauge wire. You don't need to big, since your tying that wire into a relay and factory wiring.
  5. C

    Install quad shocks

    I wouldn't say hit or miss, but your right if don't have the supporting mods or your suspension is worn out then quads may be needed. Things like subframes, control arms, upper axle bushings, springs, shocks, and pinion angle are a big part of it.
  6. C

    Install quad shocks

    If I remember correctly MM tells you to remove the quad shocks in the directions with the suspenion kit due to suspension bind. I have the MM lowers with the recomended SVO uppers and the MM panhard bar on my 00GT. It's a nice setup and handles well on the street.
  7. C

    dual focus pumps question

    I was able to push out 530rwhp on the stock 03 Cobra twin pump with them maxed out. I upgraded to the twin focus setup and did the wire mod with an upgraded fpdm so I'll have room to grow later down the road. Another upgrade to consider is the fuel line upgrade if you really want to push...
  8. C

    Install quad shocks

    I'd go with a good set of upper and lower control arms like Steeda or UPR. None of my stangs have quads, and I have no wheel hop or traction problems. I have Maximum motorsports setup on my 00, Steeda on my 91LX and UPR drag setup on my 88LX.
  9. C

    Are 89-93 GT throttle cables same as 4 or 6cyls?

    Nope, I had to change throttle body cables when I swapped my 91LX from a 4 banger to an EFI V-8
  10. C

    Head gasket woes

    Alot of the guys running NMRA renegade are running Cometic head gaskets or Felpro MLS gaskets with their blown Mustangs. While apart I'd have the heads looked at to make sure there still flat and not warped and causing you to blow head gaskets.
  11. C

    wheels for 5 lug 91 gt (Help need pics)

    Here's some 96GT wheels on my 91LX before I primer her and added the Saleen body kit.
  12. C

    Track heat heads and intake with e303 cam ?

    I have pretty close to the same combo your going with and I've been very happy with it for the few weeks that I've had her on the road. If you have no gaskets, summit racing sells a trick flow top end swap kit that comes with all the gaskets you'll need.
  13. C

    ARP rocker stud question

    I ordered some trick flow 3/8 rocker studs from summit racing. They were part #TFS-514400613 and when you open them up they have ARP stamped on the end, but the funny thing is they were cheeper than ordering name brand ARP, even though their ARP..hehe.
  14. C

    19lb injectors or 24lb

    I had my 19lb injectors on my 00GT when she was N/A and making 280rwhp and still had duty cycle left. Best bet is to take it to the dyno for some power pulls with air/fuel to check if she's going lean on the top end.
  15. C

    18's on 90 notchback?

    Just to give you and idea, I put my Y2K 18X9.5 Cobra R's off my 00GT on my 91LX with SN-95 spindles on the front and SN-95 axles with disk brakes on the rear with 275/35/18. The rear wheels would stick out past the fenders a bit along with the front.
  16. C

    19lb injectors or 24lb

    I'm running my 19's still with trick flow heads, gt-40 intake, e-cam, and 1.6rr.
  17. C

    What valve spring keeper for trick flow twisted wedge heads?

    Here's the part # that's listed in my directions that came with my Trick flow heads. TFS-51400444-1 (buy right from summit racing) This is for two keepers. You can download the directions off trick flows web site and has alot of part #'s and how too's.
  18. C

    2.73 to 3.73 gears (any problems?)

    I'm running 3.73's in my 91 and really wish I would have went with 4.10's like I have in my 00GT. Just make sure you have somebody who know's how to set up rear ends and you'll have no problems.
  19. C

    Are some roller rockers quiter than others?

    If they are set up right with the right push rods they should all be pretty quiet. I use Comp Cams Pro Magnium 1.6's and they are almost as quite as the stock setup.
  20. C

    Help plz vortech guys car boging bad below 3k

    Check the mass air meter. There may be something on it causing some problems. I'd also check the plugs and see what they look like.
Top Bottom
Back
Forums
Menu