Search results

  1. J

    por15 brushing on?

    i used the engine paint kit they offer on my block and it came out fantastic. still looks good. i'd prob do it again.
  2. J

    water pump bolts

    any parts store should have em, or at least be able to order them. if they have stuff from dorman/motormite/help it can be obtained.
  3. J

    Please recommend a good balancer

    ATI has already been stated, otherwise look at Romac/Powerbond or try Innovators West.
  4. J

    Frozen collector bolts, help!!

    if the part is threaded, you can try to heat it up then attempt to unscrew it. i would go straight to mapp gas, over the propane. if you access to an oxy/acel setup, that is ideal. if not, you may have to remove the header and drill it out.
  5. J

    What is the plug going into the tranny? *pics*

    it will either be the reverse light switch or neutral switch.
  6. J

    timing chain cover

    the difference will prob be for the water inlet/outlet for the pump. one would be for stnadard rotation, the other for reverse. for the water pump difference, i think it is a matter of just changing the backing backing plate.
  7. J

    Where did you install your wideband oxygen sensor?

    yeah for wide ban. why only one? is it cause the price of the WB O2's? i would think that you would want one on each side so you can see what that bank is doing.
  8. J

    Does anyone elses wipers skip across the windsheild?

    take the whole blade off of the wiper arm. when the end of the arm is resting on the glass, look at how perpindicular(sp) the little nub(the thing that the blade slides onto) is compare to your winsheild. adjust(careful not to break it) so that is is parrallel to it. this will put a more even...
  9. J

    Where did you install your wideband oxygen sensor?

    do you run dual or single O2's on a dual exh. setup?
  10. J

    Engine Pro's.....Help needed with rocker arm setup!!

    try this http://www.mustangcentral.net/tech/geometry.html
  11. J

    Tublar k member

    i normally would suggest AJE or PA. but i read on the corral where a guy had a prob with his and the folks at PA. long thread about it. dont have a link, but a search should find it. also remember that the MM, Griggs, QA1, Kenny brown will all mess with your wheelbase some. sothat means...
  12. J

    Low oil pressure?

    old rule of thumb is you want 10#'s per 1000 rpm.
  13. J

    Need help with external shift light

    normally the wires goes like this: green - tach signal. or negative side of coil white - illumination red - key on positive black - ground by the sound of it, you would hook the yellow to your shift light, and then the other wire on the light to ground.
  14. J

    any KC area local mustang forums???

    you can try www.purposebuilt.org www.kcmustangs.com www.kcsr.org this is a all around forums, import and domestic
  15. J

    Load Leveler from ebay?

    how much is shipping? that kinda also adds to the total price. i have an A/C delco leveler and it works fine. one thing to look at is the handle area where you turn to tilt the motor. mine is weak and accutally broke off. i had to use a rachety wrench on it to turn the motor. this is the...
  16. J

    351 shorty headers

    he does have a nice kit. seems to be making about 25hp per pound of boost. it was slipping on the dyno a little though. if you get bored go here and take a look at it. http://weekendwarriorz.com/keith.html
  17. J

    351 shorty headers

    they are my buddies. he went to a turbo setup and doesn't need em anymore.
  18. J

    351 shorty headers

    BBK chromed or whatever they call it.
  19. J

    351 shorty headers

    shameless post to plug my sig if anyone is interested.
  20. J

    wheel bearings

    big pair of pliers should do the trick. it isn't on there that tight as stated already.
Top Bottom
Back
Forums
Menu