Search results

  1. 408stroker5.0

    Please check if my pinion bearing is busted!!!!!

    You need a Hyd. Press But you could easily go and purchase the bearing from your local retailer and then take the pinion gear and bearing to a decent Garage/Auto Repair Shop and they'll probably press it on for you for next to nothing. Shon
  2. 408stroker5.0

    Please check if my pinion bearing is busted!!!!!

    Dont use it. That Bearing is Finished. For the amount of time and money it will cost you to get a new Pinion Bearing Pressed on I'd definetly get a new one. Shon
  3. 408stroker5.0

    high oil pressure ??

    It also could possibly be that your bearing (ie:Rod, and Crank) Clearences are to tight/past spec which at times can cause excessive oil pressure. But I'd start with the simple thing's like Gauge, Sending Unit etc. etc. Try a new Mechanical Gauge and see what you get. In terms of Your Oil Pump a...
  4. 408stroker5.0

    electric blower,supercharger

    Combine That Electric Supercharger with a Super Dialithium Transfuctioner DuHickey And A New Carburetor Belt And You'll Be Seeing HP Gain's in the 100's!!!! And Then.....:Track:
  5. 408stroker5.0

    new clutch for a 9 sec street car

    One Word....McLeod. I'm running a complete McLeod Setup( Bellhousing, Flywheel, Disc, P/Plate etc.) behind my TKO. There Tech Support is Great As Well. I ended up talking to Red (The Owner Of McLeod) and he was a great help. Ended up using everything he recomended for my set up. I'd recomend...
  6. 408stroker5.0

    Good Carburated Intake

    Uhhh....I had an Offenhauser Port O Sonic Single Plane intake on an old 375HP 351 Combo of mine. Needless to say I was very dissapointed with that intake, ended up getting rid of it and going with a Edelbrock Torquer II single plane that I had laying around. Anyhow, I'd say your combo would most...
  7. 408stroker5.0

    Good Carburated Intake

    It would be nice to know more of your engine and drivetrain spec's to really narrow down what would work best for you, but you did say your looking for street use and you dont go to the track so I imagine your running a pretty mild setup. For street/strip engine combo's I've alway's liked the...
  8. 408stroker5.0

    Chassis Dyno's In The Edmonton Area

    Right On....I'll look those guy's up and give them a shout. THANX!!! Any Others?
  9. 408stroker5.0

    Chassis Dyno's In The Edmonton Area

    Just planning ahead for next Spring, and was wondering if anyone had any good recomendation's or experience with any Chassis Dyno's in the Edmonton Area. I'm hoping to fine tune the Mustang and see what kind of number's I can get out of her so I'm not afraid to spend money were it counts. Any...
  10. 408stroker5.0

    What everyone's projects for the winter?

    Finnaly got all the parts for my Moser 9" together...That will be going in this winter which will be pretty much complete the Mustang. New Project: 1964 Galaxie 500XL which I just picked up out of the bush last week in need of a resto. Going to be Primarily a Street/Show Car. 460 (Shootin For...
  11. 408stroker5.0

    What about those electric header dumps, are they worth getting

    There nice for the track...that's about it. One other issue... Fox body Mustang's dont have a whole lot of room underneath for these cutouts. They will fit but ground clearence becomes a bit tight especially since you should mount them facing to the ground abit instead of right up against the...
  12. 408stroker5.0

    11:1 Compression Anyone?

    I'm running close as well with my 408(Details in Sig)...10.8:1. I run 92 Octane Fuel and throw in some good quality octane boost as well just for a little added comfort. I'm currently running Lucas Octane Boost which seems to do just fine. I drive it on the street without any problems. Just try...
  13. 408stroker5.0

    oil pump or guage problem?

    Definetly most likely the oil pressure sending unit... they do go every so often. Try replacing that first as it's fairly cheap. It's located on the left side near the oil filter just incase you didn't know.
  14. 408stroker5.0

    Chrome spray paint for pony rims?????

    Don't Do It.....Plain & Simple. It may look good at first but paint is not durable enough to hold a long lasting finish on rims...in my opinion painted rims look kind of taky anyway. It wont be long before it starts to fade or flake off. Also that chrome paint you can buy in stores dosn't look...
  15. 408stroker5.0

    What did you guys torque your alluminum heads to?

    Go by the head Manufactures Torque Specs only. Torque Specs vary among different manufactures and cylinder heads.
  16. 408stroker5.0

    86 gt with stock flat top pistons. Forged yay or nay?

    Yes They Are Forged
  17. 408stroker5.0

    Western Canada People

    Bonnyville, Alberta (2.5 hours away from Edmonton)
  18. 408stroker5.0

    Looking for link for stroker 408

    I clearenced mine before taking the block to the machine shop by doing it the mock up way. Time consuming for sure, but definetly the best way to do it and it's fairly easy. I used some used bearing's I had laying around that were still good and lubed everything up inorder to not scratch up or...
  19. 408stroker5.0

    What carb would you run?

    650 Speed Demon Vac Secondaries or Mechanical(Your Preference)....Plain & Simple. Why buy a Holley 650 DP (Which Is A Good Carb) when you can buy an improved version of it (Speed Demon) for only a bit more?? Shon
  20. 408stroker5.0

    Western Canada People

    You Said It........ :nice: :p
Top Bottom
Back
Forums
Menu