Search results

  1. G

    Oil In intake

    I had a performer intake and it sucked oil like crazy. The baffle under the intake is very small and doesn't cover much area and on mine it was bent such that it caused gravity to pull oil towards the PCV valve...not good. Start by bending the baffle so it will allow gravity to pull oil away...
  2. G

    I need help

    I'd try an Oxy-acetylene torch with a rosebud tip. Try to evenly heat the outer circumference then tap with a hammer gently to get them to break loose. Good Luck, Don
  3. G

    Help! Surge on Cruise Control Only??

    Don't know in your case. I added SC and built motor and my 90GT cruise still works great without surging. I had an 82 Suburban 6.2L diesel and added a Turbo and it surged while on cruise control, so I had to remove a small restrictor plug that was in the vacuum port on the cruise module. It...
  4. G

    are these the mufflers that come on the magnaflow kits?

    Those look like and the dimensions seem like the ones that came with my Magnaflow catback for my 90. Don
  5. G

    What else could cause a vibration???

    Ford has new driveshaft bolts under N-800594-S100 they are 12mm x 1.75 with a 12mm 12pt head. YMMV, Don
  6. G

    Underhood Equipment Question

    I don't see no stinking diagram. :-) OH, click on THIS....good stuff! Don
  7. G

    rear tire help

    On my 90GT with quads 255/40R17s on 17x9 Cobra Rs would rub slightly on the quads from cornering. I now run 275/40R17 Nitto 555 DRs with MM Lower control arms and no quads. That's about all you can run without mods. Don
  8. G

    "Noise vibration harshness" (NVH) opinions needed

    Things to check: 1. When my front struts needed replaced I dreaded every small bump in the road....talk about harshness. After replacement no worries nice and I don't have to worry about every little bump. Problem is it just sneaks up on you. 2. With rear gear ratio changes you mess up...
  9. G

    adjustable fpr - pro's and cons?

    An APR will only allow you to push (act like larger ones) your injectors if they are marginal. The PCM will adjust for idle and normal closed/open loop operation. If you have plenty of injector then you don't need one. I run a stock FPR with my setup and 42# injectors, works great with my...
  10. G

    need help finding the right head gasket

    dragnazz5.0, My next set will be ROL. They are suppossed to be real strong and not too expensive. See this link: http://www.store.partsdinosaur.com/product521.html Good Luck, Don
  11. G

    innovate standalone??

    jimsstang91, I think what you described is what happened to mine. Mine worked fine at idle and then 5 min. of driving and pegging lean. This was due to the sensor overheating, I made a heatsink out of a sheet of copper that is 4"x4"x0.062" and drilled a hole for the sensor to fit in the...
  12. G

    Satan causes intermittent power loss/bucking?

    I vote for the ignition switch. The +12V to the coil and power to energize the starter solenoid do not connect to the PCM. When my ignition switch acted up and I changed it out it literally flew apart in my hands when I removed it. You'll need a special torx bit with a hole in the center to...
  13. G

    Tired of replacing header Gaskets!!!

    My JBA shorties came with a set of header bolts with special lock washers. Those and FlowTech Real-Seal aluminum exhaust header gaskets 99253FLT trimmed to fit. No leaks or issues here so far. Don
  14. G

    Did I damage my fuel injectors (with pics)

    InMyPrimeSVT, You'll need to get new o'rings and get the old ones out of the fuel rails. The top and bottom use the same o'rings. Don
  15. G

    pinging,studder,miss fire etc. *help*

    str8stangracer, Never mind.....re-read post. Don
  16. G

    Calling KB and 306 users

    Yeah, it is definitely worth it. Mine has been a bear to tune but almost done. Blowzilla with 10# pulley, makes 8# on my 306, Edelbrock 60379 heads, Explorer lower, Crane 2030 cam, 42# injectors, 70mm TB, stock inlet and air box w/ K&N panel filter, stock FPR and 190 L/hr pump, stock block...
  17. G

    14* timing on 85 octane...

    Yeah, I was running 16* timing with 87 Octane when my 306 was NA. Don
  18. G

    speedo/odometer calibration

    local speedo shop, they mostly calibrate truck speedos. Don
  19. G

    ACT gauge???

    See this for the ACT transfer function: http://www.geocities.com/dbennettya/Mustang_PCM/act_comparison_2a.xls Don
  20. G

    HEADERS: edel vs bbk vs ??

    I recommend JBA headers...very high quality. I had a set of BBK ceramic coated headers and they cracked near the welds after just two years. The JBAs are premium and make the BBKs look like junk. Don
Top Bottom
Back
Forums
Menu