Search results

  1. kah9911

    serpentine belt

    about 10 min hard. expect the diagram in the Haynes manual is wrong for the 99+ cars. but still only took 10 min.
  2. kah9911

    Slotted & Drilled Rotor Question

    http://discbrakesrus.com/make/ford/mustanggtff.htm lots to chose from!
  3. kah9911

    MIL eliminators required???

    thanks, I was wondering what the rears controled. -Kevin
  4. kah9911

    MIL eliminators required???

    So the rear o2 censors will not affect the driveabilty of the car. make it think it is running lean or rich?
  5. kah9911

    Installed U/D pulleys, no A/C

    I dont run the AC but i have had the defrost on and it worked like normal. sound like something else is wrong.
  6. kah9911

    Banjo bolts and copper washers cobra brakes HELP ME

    I just put a set of cobra brakes on my 01 gt and didnt have a problem with the banjo's but the other end that conected to the hard line was not the same so I had to use my old rubber lines. wasent happy about it but it worked just fine. good luck- Kevin
  7. kah9911

    Cobra brake kit for GT

    They provide A LOT more brakeing! I got mine from brakes r us. I got the yellow calipers. (I have a 01 zinc gt) http://discbrakesrus.com/make/ford/mustanggtff.htm
  8. kah9911

    How to break a weld?

    If you can block the exhaust to keep it from moving you can break it with a chisel and a hammer, IF it is a small weld and not have to worry about your exhaust.
  9. kah9911

    Did the Gas pedal mod.

    I did this about 6 months back and have no problems. I did feel a difference, not much but it was there. I used a nylon spacer that I cut a with a hack-saw and just popped it right on. No clamps or anything. I can take a pic if needed. http://www.mustangworld.com/ourpics/fcar/99pedals.htm
  10. kah9911

    Concord Mall Mustang Show- Aug 7 & 8

    I was on the way back from the airport yesterday and saw on a billboard that there is a mustang show "mall wide" at the concord mall. Figured I would let everyone know. Also its real easy to get to, right on 202 ~5 miles north of 95. Tried to check if there was any registering involved but I...
  11. kah9911

    More power with synthetic oil?

    I dont think you get more power (only in theory due to less friction) but I think it helps engine life. Plus its so pretty to look at when pouring! You can tell is finer. Just my .02.
  12. kah9911

    Clay Bar = AMAZING!

    it works VERY well. Last time I waxed my car it got a bit wet and some of the wax didnt come off. the caly bay took it off no problem. it also really brings life back to your paint.
  13. kah9911

    Weight Transfer- Struts or Springs

    So you think the high spring rate will undermine the "soft" settings of the springs. I do plan on getting a set of drag radials in the future but since I drive on the street everyday and only go to the track a couple time a month, at the most, I would rather have it handle nice and clean...
  14. kah9911

    Springs, Shocks, and Struts Oh my!

    I am also going with the H&R race springs but am going to get the Tokico 5 way shocks so I can soften it up a bit for the strip.
  15. kah9911

    Weight Transfer- Struts or Springs

    I am planning on getting H&R race springs and Tokico 5 way adjustable struts (I love the twisties) but the question comes in when I am at the strip will putting the struts down to 1 for launching do anything with such a high spring rate. In summery which (springs or struts) lets you transfer...
  16. kah9911

    Writing on my engine block

    it is all from the assembly line so they know what is going where. my exhaust had "BOB" stickers on them and my spare tire has "PONY" written on it. I even got a factory installed rubberband on a wiring harness.
  17. kah9911

    GT E.T

    jack up your rear and have someone rotate the tire around while you lay under the car and let us know what you got? :shrug:
  18. kah9911

    How to make the stang handle reallly good

    road racing is a lot to do with managing weight and the IRS is somewhat heaver than the live axel so from that stance keep the stock rear.
  19. kah9911

    PIC REQ: Black Stangs w/ black wheels

    how about some yellow cars with black wheels?
  20. kah9911

    Stock Intake Sizes

    I have been having some trouble with my MAF so I took the intake off to see if it needed a cleaning. While it was off I started measuring the components and they were all bigger than I had thought came stock: ~79mm MAF (smallest point, inlet is 91mm) ~73mm TB w/ no reduction at Plenum...
Top Bottom
Back
Forums
Menu