Search results

  1. pdl2flr

    Mac ProChamber from partShopper.com

    To me that third piece looks like the bell flange that connects to the drivers side header. Can't tell from the first picture of the whole pipe but maybe it slides inside the mid pipe at that connection. Maybe its designed that way to accomodate different types of connections for different model...
  2. pdl2flr

    mac H pipe question

    You only use one gasket for the passenger side header connection. The drivers side is a ball/socket type connection that does not use a gasket.
  3. pdl2flr

    Installed MRT H-Pipe w/ Flowmaster AT Catback

    I installed my MRT H-pipe w/cats (stock cat-back) last weekend and had no problems, fitment was perfect and had no leaks at all. I installed it with just the front wheels up on ramps and the rear wheels raised a few inches on jack stands. Did you use the new passenger side gasket that was...
  4. pdl2flr

    Help with prochamber installation!!

    I just installed my MRT H pipe this morning. It came with a new OEM passenger side gasket which I used. MRT also recommended putting a bead of High Temp RTV silicone sealant on the inside of the bell flange on the drivers side of the mid pipe. So far everything seems to be sealed up fine.
  5. pdl2flr

    xpipe install???

    I just installed my MRT H-pipe this morning with the car up on ramps. The passenger side bolts look more difficult than they are. I used a 15mm 6pt. deep socket with swivel and a 10" and 6" extension together and had no problems. You just have to find the best angle so the socket fully seats on...
  6. pdl2flr

    MRT H-Pipe w/ Flows

    I hope to have my MRT H-pipe installed this weekend, although with stock cat-back for now. I believe I read in another post that the O2 sensors on the 2004 Mustangs are located differently thus requiring extenders with most aftermarket mid pipes. Maybe someone else can confirm?
  7. pdl2flr

    Looking for an Aluminum Driveshaft for '03 GT!

    I bought mine right here on-line from PartShopper. Just go to DriveTrain and then to DriveShafts. Received mine in about 3 days.
  8. pdl2flr

    Aluminum Driveshaft

    I know this thread is old but I have had my Aluminum driveshaft for a month now. I can't say I feel any performance increase, but the car does run a bit smoother and I swear I have gained 1-2 mpg since I installed it. I was always dead on at 22 mpg but have now been averaging 23-24 mpg. At least...
  9. pdl2flr

    hi flow cat h pipe

    To those with the MRT H pipe. Did you have any problems with leaks at the mainfold flanges? or did you replace the studs with the fully threaded NAPA ones. ps. does anyone know if the MRT H pipe that they sell here on PartShopper is the lastest version. Ninosports advertises that they sell...
  10. pdl2flr

    Install ? for strut tower brace

    Go to Steedas web site and look under "News & Tech Articles". There are instructions for the Strut Tower Brace installation. http://www.steeda.com/
  11. pdl2flr

    Aluminum Driveshaft

    Just puchased mine from PartShopper for $190 shipped. But I have seen them for around $175.
  12. pdl2flr

    MM&FF Plenum article, have a question.

    If your talking about the C&L plenum test, they tested with the stock 65mm TB and a Ford Racing 70mm TB.
  13. pdl2flr

    Vibration in Car

    I have an 03 GT vert with the exact same problem. My vibration is pretty much contained between 60-70mph, and smooth everywhere else. Two previous trips to the dealer and all they would do is rotate and balance the tires. I am taking it back one more time and have them specifically check the...
  14. pdl2flr

    Oil change every 3k miles...

    When changing your own oil in a GT, how high can you lift the front end and still have the oil drain properly. I have a set of Rhino ramps, will these be sufficient. I have always owned trucks prior to my GT and I could easily just lay underneath and get to everything.
View older results
Top Bottom
Back
Forums
Menu