Search results

  1. Mach1steve

    Trying avatar

    nice project Good Luck with your project...... they are sure are fun when they're done ! Mach1steve www.muggziperformance.com
  2. Mach1steve

    SERIOUS BOGGING PROBLEM at the track

    Carb dry sounds like you are running out of fuel, ie. the fuel bowls are emptying faster than the pump can fill-em back up again. Check the float levels to make sure they are filling to where they are supposed to be..... and maybe check fuel pump function. Just becuase it's a Carter fuel pump...
  3. Mach1steve

    Help would be much appreciated

    You can use 1974 to 1980 model Ford Granada/Monarchs for the Disc brake conversion.
  4. Mach1steve

    which carb+intake kit?

    used there's usually lots of both of these at parts swap meets....... find out where they are and save a ton of $$$ it's also more fun Mach1steve www.muggziperformance.com
  5. Mach1steve

    351x will swap right into a 67 stang right?

    headers I beleive these guys sell headers for this swap, www.fordpowertrain.com expensive headers, but they fit well, and are probably the best headers on the market for your Ford, no matter what model you have.
  6. Mach1steve

    Yet another rear end question

    gear tolerance When you installed the gears, do you know what the angle is supposed to be and the tolerance ? Or did you just wing it ? Not criticizing, just curious so we have more info.........
  7. Mach1steve

    Talk forum: 2 word story

    stole from
  8. Mach1steve

    Which brake pad?

    source for good Pads I do a little Road Racing (only 2 events a year) but mostly just Street Cruisin. I use the Porterfeild R4-S Brake Pads. They take the heat better than stock pads, are easier on your Rotors (which are expensive) and are quieter. They work like stock pads when cold, so...
  9. Mach1steve

    rod bearing question

    correct Brian is correct no grooves on Rod bearings
  10. Mach1steve

    I need help?

    thump in your pocket-book I am not an "engine expert" but the simple rule here is, if there's a knock, there's play, and where's there's play, there's wear, fatigue & part failure. Lets say you leave it alone....... it breaks and punches a hole through the side of the block (and it will, where...
  11. Mach1steve

    1970 351C 2V Project...Input Requested

    Sounds like a fun project ! 1st ...put in the 3.55 gears & Trak-Loc rear (that's "Posi" in Chevy talk). You will immediately notice the car feels much faster. 2nd...Edelbrock makes a 4V Intake to fit the 2V heads.... get one (part# 2750). 3rd .... the Holley Street Avenger 670 is a good...
  12. Mach1steve

    Holley question

    sounds like a rebuild is needed to me. I have a used 3310 750 if you want it ? Works fine, I just swapped it for a 650 Dbl Pumper (goin racin). Mach1steve www.muggziperformance.com
  13. Mach1steve

    engine problems need help

    power valve If it was a Holley Carb I'd say it was the Power valve on the Carb, but I don't know much about Edelbrock Carbs. Find out if you have one on that Carb and if so it may be Kaput. It's an in-expensive part. When blown (at least in a Holley) they make the car run VERY rich, and bog...
  14. Mach1steve

    OT: What does everyone do for a living

    Product manager - Beer ! I am a Product Manager for a large Packaging Company. I look after all the Microbreweries across the US & Canada.... yes I get free Beer ! I also own a small High Performance auto parts company that specializes in Classic & Late Model Mustang Brake Upgrades.... check...
  15. Mach1steve

    kyb shocks

    I use em on my 70 MACH1 I have the KYB Gas-a-Just shocks on all 4's. They are firmer than the GR2's I beleive, but I like that as I Track my car a couple of times a year on a Road Course. Doesn't seem harsh to me on the street. I hear the Koni's are great too, but haven't tried em...
  16. Mach1steve

    Rear End

    sounds to me like it could be any of the following; 1) check your Universal joints, could be loose or worn. 2) check for play in the rear axle bearings (jack up rear end and see if you can wiggle the back wheels around by grabbing them and jiggling) You get play ? you got worn out bearings in...
  17. Mach1steve

    brake upgrades

    Hey If any of you guys are interested in Brake upgrades, these guys sell Crossdrilled & Vented Brake Rotors for our Classic Mustangs...... cheaper than Mustangs Plus by alot ! US made castings too, no off-shore junk. 1970-73 Crossdrilled & Vented Rotors = $ 175.00/pr. I think Mustangs Plus...
  18. Mach1steve

    Biggest wheel that can fit in a lowered '69 Mach1?

    what size Rim ? (dia.) I have a chart that tells you what size non-0stock rims and tires fit, but once you lower the car, I don't know how accurate it is. The lowering may effect the accuracy of the information. If you want to send me your E-mail address, I can e-mail you the chart...
  19. Mach1steve

    Front Cam Bearing - is placement critical?

    check em all if one is wrong, other could be. Rule of thumb..... check twice, rebuild once.
  20. Mach1steve

    15" x 8" Styled Steel Wheel???

    Mustang Tire Chart If you send me your e-mail address, I have a chart that tells you the rim off-set you need for all Mustang nodel years, and the Max receommended size tire, all the way up to 18" rims. Mach1steve www.muggziperformance.com
View older results
Top Bottom
Back
Forums
Menu