Search results

  1. S

    fox body parts

    How much for the 140 mph speedometer cluster? The whole thing Price for GT third brake light? Do you have gray visors? How much? How good shape the front GT bumper? How much? Thanks Skip
  2. S

    F- CAM Questions !!!

    Used my Fcam with on a carb. setup and rpm heads. Went 12.6@106 on 7cylinders. kifter on number6 cylinder wouldn't prime up on the intake side not letting any air into that cylinder. Idled at 850 and no bucking or jerking. Drove smooth
  3. S

    T-5 questions

    Should have very little like thousandths of an inch
  4. S

    AFR 225s for 408 stroker???

    Thats why I have decided to go with the 205's. Won't be to big or small. Later down the road if I want more power I can always have them ported. Ask Ed Curtis
  5. S

    McLeod or Lakewood Bell Housing??

    I just ordered my T56 for my 88 GT and got the McCleod steel bellhousing. They all might need alittle filing on the outside.
  6. S

    is he right???

    I dont think you will but that will depend on the rpm of motor and hp. If you are even at the top of the gear. I would go with the 4.10's for now. You would have more fun. And besides the 3.73's are cheaper so I'm sure if you did decide to go with the 4.10's you could sell them and get the 3.73's
  7. S

    Thinking Of Going Carb, Pros?cons?expiriences? Please Give Suggestions

    My car went with fuel injection 13.7 and took that all off put on a holley 650 doublepumper and weiland 8011 intake. Went 13.299 twice. Same slicks and it was hotter when I used the carb. by 14degress. If you dont mind the get in and go on cold days (you cant do that with a carb unless it has a...
  8. S

    Any sort of 351W heads available for a 5.0????

    the 289's would be better if you compared them to the E7's cause of better compression ratio and they can take alittle more porting
  9. S

    Can you install cam.....

    YES just remove rad. and then turn the ac out of your way. You dont even have to discharge the ac
  10. S

    AFR 225s for 408 stroker???

    I'm in the process of building my own windsor 398 74 block, put 4 bolt mains on 2,3,4 caststeel crank billet I beam rods forged pistons 4340 10.3 compression ratio with 60cc heads I'm going to use the AFR 205's and should be between 525 and 550 hp. I'm going to use the victor jr and 1...
  11. S

    Head gasket install question

    I put sealant on all of mine and the water holes go towards the front!
  12. S

    Efi To Carburator Swap

    Pickup tube for gas tank or sump pan welded on Fuel pump (holley blue pump is good and comes with regulator) 1/2 fuel line and fittings (get fittings at local store that way you can keep going back and getting what you need, or get a fuel line kit from summit) Distributor...
  13. S

    cam choice?

    F cam will work with no piston to valve worries!(that was even with performer RPM heads with 1.90,1.60 valves and 1.6 roller rockers) I would change springs if using stock heads. If you go to something other than that E or B will works also. Make sure no more than [email protected] and a total lift of no...
  14. S

    NMRA Race in Reynolds

    Went last saturday and was impressed with the drag racing! The swap meet and car show sucked! Hardly any vendors and the people that were selling stuff it was junk for to much or just worn out worse than what I have. And maybe 15 cars in the car show! What advertising on nothing
  15. S

    Post whoring for those who lost counts

    Its helping me and any guy that says it isnt, WELL we will just say they are LIERS ! ! !
  16. S

    MD,DC,VA and others

    You didnt say anything about PA ! :damnit: So here goes Im Skip with a 88gt in the process of a windsor swap. I spend most of my cruising time in Hagerstown MD.
  17. S

    What springs on AFR 205s

    I was looking at a comp cams int ex @50 242 250 total 576 600 I was hoping to have this done for carlisle PA june3-5. But its not going as plaaned. Im in atlanta ga for work for a couple of more weeks and I live in chambersburg PA. Really interested in the...
  18. S

    What springs on AFR 205s

    I,m almost one hundred percent sure with going with the AFR 205's. Ive noticed that a few of you have them. What springs do you have on them? Im going with a hydraulic roller setup and was wondering how high they will rev with what cam and springs? Is it worth me to get the beehives? What to rev...
  19. S

    Hydraulic lifters in 351w

    Im looking at a comp cams .242int .250ex and total being 576int 600 ex. Or maybe a custom one from ed curtis
  20. S

    Transmission questions...

    Had this happen in two different cars. One was my car the other was a friend of mine. His was the input shaft going bad and mine was right after I installed my clutch. Mine was my throwout bearing I was in the car pushing down the pedal and my friend was underneath adjusting the clutch. He had...
Top Bottom
Back
Forums
Menu