Search results

  1. 1

    Anyone know original ride height 67 FB?

    Hi Mike, sorry I don't have an answer but check on Ebay, there are some frame spec sheets from a body shop manule for sale...wait try a body shop they might have one for you to look at. Vince
  2. 1

    PCV's and Breathers? Some questions

    Hi, unmetered air...sort of. Its regulated by the valve itself and is a mixture of blowby and air. Look at the common stock set ups. The breather in in the air cleaner housing. This is considered a closed system cause its in the air cleaner housing, but its still out side air. If you...
  3. 1

    MSD 6 Box

    Msd hey guys, you can just run off of the original ignition wire. That wire is just an on off switch for the control box. its a 5 volt min circuit. The original distributer wire will do fine. Just be sure to wire up you ignition switch so you get voltage when cranking. I've seen guys tap...
  4. 1

    Intake experts: PCV issue (long)

    vac Hey B, wow thats high in gear...i'd say you have your carb blades opened up alot. Im willing to bet you transfer tubes are uncovered. Tuning is a must. good luck,let us know how it turns out. Vin
  5. 1

    Intake experts: PCV issue (long)

    stinky Hey guys I work on diesels and I gotta agree diesels stink but are very usefull. Fuel efficient and POWERFULL! The reason why they still use road draft set ups is due to the lack/or no vac created by the engine. Anyways, the min in gear was 5-7 and idle was to be higher. It will...
  6. 1

    Mustang Fender Flares?

    nice Hey Mdjay, I must say that you have "sinister" down pact. Im going to be in Vegas for the SEMA show like to stop by and go shopping. Vin
  7. 1

    Intake experts: PCV issue (long)

    Pcv hey B, do you have a PCV valve hooked up to the full intake vac side? You should.The valve acts as a regulator. You are right if its full vac. You have a vac leak. In gear depending on your cam man vac reading should be around 5-7 inhg. 19-20 in park. Vin
  8. 1

    Driver side rear wheel whobble

    wobble Hi Ryan, well if the other wheel (left rear) is ok try to mount it on the right side then check again, you can safely jack up the rear of the car and support it with jack stands to check. If the wobble moves to the other side then its your rim/tire. If the wobble stays on the same...
  9. 1

    Mufflers

    Hey Ron, Is that what are you running on your fastback? I saw it drive by one day and it sounds great. Do you still have it? Haven't seen it around lately. Vin
  10. 1

    1965 Fastack Restomod (PICS)

    Hey Capps, looks good, mag car? you will need some work but its not hopeless. The problem with the car is that on some aspects it looks modern, other aspects its very dated. You gotta go all the way with it or park it in your garage. The place I would start is your engine bay, looks 80's...
  11. 1

    need holley commander 950 help

    Hi Tom, If I remember correctly you will need a blower map sensor, one that will calculate or register boost...try posting here www.lateral-g.net for info, lots of Holley guys there.
  12. 1

    The SN65 project car

    Sn65 I read on another forum that he was going to be out a few days... patients :D
  13. 1

    how can I tell how much lift my valve springs can handle?

    boooiiinnnggggg nice avatar BTW...I know its a cartoon but I can't help but look. :rlaugh: well its tough without a spring tech card...can you get the guy you bought them from find a reciept or pn?? He has to have something unless he's BSing you. All is not lost, you can pull one then...
  14. 1

    Wheel bolt pattern for 1969 Mach1

    Hey there, Uni pattern will have oval shaped stud holes and will come with special washers that makes up the bolt pattern. better idea, grab them rims sell them on ebay...swap meet... etc and buy rims you like. Them chevy guys buy anything. like me ;0 Vin
  15. 1

    Idle confusion

    Hi Matt, sounds like your in need of a good carb tune. Increase the idle fuel/air ports. Edel's(AFB) are can be tricky, if you don't have the required tools any tune shop can work it out for you. Good luck and let us know how it comes out. Vin
  16. 1

    Roush Lets Go Roushers, Get Your Pics Up!!

    hey... Didn't want you to feel alone... nice R' BTW :nice: this one is my fav. Vin
  17. 1

    96 Cobra *thump*

    Hey now, I have run into 2 separate problems that could cause your problem, worn/broken rear link bushings and/or worn trans mount. Best bet would be inspection on a rack.G-L Vince
View older results
Top Bottom
Back
Forums
Menu