Search results

  1. stanglx2002

    Build Thread Enola- Finishing touches

    What's the next thing that you are installing on the car then?
  2. stanglx2002

    Anybody try these center vent pods ?

    Those look great. Im glad you took the time to clean them up to make them look factory. This is a big reason why I enjoy 3D printing
  3. stanglx2002

    Build Thread 1978 Fairmont. I bet somebody back home’s thinkin’…I wonder why he don’t write..?

    YOU! Oh, and purdy please paint that red catch can
  4. stanglx2002

    Progress Thread She’s a runner

    Left to Right - Sensor Ground - TPS Signal - 5V VRef
  5. stanglx2002

    spark plug wires, what are we using these days?

    I typically lean to getting the 90* for a couple reasons of smaller boot footprint, clearance between header tubes stock or aftermarket, and easier to reduce the length of the wire itself due to point straight up.
  6. stanglx2002

    Progress Thread She’s a runner

    Thank goodness you decided on relooming that harness, because that could have made you pull your hair out with a bad ground like that especially if its the sensor ground or injector ground to the ECU.
  7. stanglx2002

    spark plug wires, what are we using these days?

    There are reasons for the different part numbers from MSD. Each part number you were looking at comes with a different spark plug boot end as they come in 90*, 120*, 180*, and Multi-angle. You buy them based on your needs, since many like the 90* to gain additional room for headers especially...
  8. stanglx2002

    Build Thread Enola- Finishing touches

    Not when you live in FL, so no need for rust prevention coating.
  9. stanglx2002

    spark plug wires, what are we using these days?

    Oh no you didn't just go there... :stir: :pop:
  10. stanglx2002

    Build Thread Dustys has a new friend

    I wouldn't put bondo on those, but a couple coats of primer filler would be better solution IMO
  11. stanglx2002

    Progress Thread Finally got my first Fox Body - 1988 GT

    Why not just take the one off the stock shifter?
  12. stanglx2002

    Looking for tuning help in Houston - w/ Tweecer

    This should answer a good amount of your questions of the differences between the Moates and the Tweecer: http://eectuning.org/forums/viewtopic.php?f=5&t=14004 They are both chips that plug into the 25+ year old computers that are all slowly starting to fail. Don't let the A4LD stop you from...
  13. stanglx2002

    Microsquirt v3 base tune

    The DIYAutoTune base tune is a good starting point. The question is did you update the setting for the engine that you are running meaning injector sizing, engine size, etc? Also, to further assist could you please post the tune file that you are using.
  14. stanglx2002

    Build Thread Enola- Finishing touches

    :nonono: Floridians
  15. stanglx2002

    Progress Thread She’s a runner

    Are you upgrading the piping for the ECT sensor as well :hide:
  16. stanglx2002

    Megasquirt Digital Dash

    0V = -28.69 5V = 313.01
  17. stanglx2002

    Megasquirt Digital Dash

  18. stanglx2002

    Anybody try these center vent pods ?

    It will need to be made of PETG, ABS or ASA
  19. stanglx2002

    Anybody try these center vent pods ?

    Agreed, the layer height looks to be way to high at probably .2 or .26 and should have been lowered to like .12 or .08. Nobody wants to wait the extra time for a better finish.
  20. stanglx2002

    Anybody try these center vent pods ?

    Yes, you are correct that the vents are 3D printed. You can paint with high build primer and painted to match the interior.
Top Bottom
Back
Forums
Menu