Search results

  1. S

    Exhaust leak prevent?

    Um, no. Where are you having the leak at?
  2. S

    Really could use somebody's help!!!

    Codes first, but EGR sounds like a good place to check. My ex's car had a similar issue, and it turned out to be the EGR valve was sticking open causing too much exhaust going into the intake. It wasnt a 5.0, but the principle is the same.
  3. S

    Really could use somebody's help!!!

    What year is your Fox? Carbed or FI?
  4. S

    Got a problem t-5 related...

    Does it seem to be engaging correctly with the engine off (can you cycle through the gears)? From what I remember, there is a little nylon bushing that sits in the receiver and the stick sits into also that keeps the shifter ball from whacking around. Check that... also, did you buy your...
  5. S

    Interesting Smoking Issue

    +1 on the valve seals. Just keep an eye on your oil level from time to time.
  6. S

    AC delete pulley

    It should work just fine, it just looks like junk next to the march aluminum brackets.
  7. S

    HELP with wiring

    Repair manual would have wiring diagrams, either a Haynes or Chilton.
  8. S

    AC delete pulley

    +1 on just deleting the AC and moving the PS pump. I opted to go with the billet PS bracket kit from pro 5.0, but it looks just like the one you can get from CFR Performance. Since you already have march brackets, I'd go with the march bracket so they match. Depending on which kind of March...
  9. S

    Bad Shifter Rattle

    There is a nylon bushing/insert in the receiver where the shifter goes into the transmission. If that is worn or gone, it could cause a rattle. Just put the shifter in neutral, unbolt the 4 bolt on the top of the shifter plate , pull up the shifter and see if that insert/bushihng is there...
  10. S

    Dome light problem

    I may be mistaken, but I think the door ajar switch on the SN95 cars was in the bottom rear of the door jamb ( by the bottom of the rear of the door, but on the body)
  11. S

    HEAD GASKET ?s

    What do you want to know? Pull the heads, clean the block and head, replace the gasket, torque the head back down.... It would be good idea to get the heads checked. They do warp sometimes and need to be trued up ,
  12. S

    will this fit??

    Physically I believe they will fit, but I think the wiring harness changed after 89
  13. S

    Misfire Cylinder 1

    +1 on the coil pack. Same issue here and ended up being the coil pack after replacing everything else.
  14. S

    90-93 black dash and more

    Did the ROHs ever sell? Do you have any more black interior parts?
  15. S

    1993 COBRA BLACK CENTER CONSOLE

    This pic links are broken, can you post another pic? I am very interested.
  16. S

    PARTING 93 GT BLACK INTERIOR

    PM Sent
  17. S

    need help from guys with electric fan onwers

    I know its more than most want to spend, but I put in the mishimoto dual fan kit. It comes with an aluminium shroud and two 12" electric fans pulling 933 CFM @ 8A each. You will need an electric fan control unless you just want to rig up a switch or something to turn them off and on manually...
  18. S

    Dummy computer on idle RPM?

    Sounds like a dirty/bad IAC/ISC or a vaccum leak. I would start by cleaning he throttle plate and the IAC first, then look for dry rotted, broken, or disconnected vaccum lines.
  19. S

    Swap done... misfiring bad though

    The only reason I mentioned the plugs is that alot of ppl think that platinum plugs are better, etc... when that may not be the case. I put platinum plugs in my wifes v6 and it ran like crap... switched it over to copper and straightened all of her misfire problems out and saved me monet to boot.
  20. S

    Codes and crappy idle

    Well, if you do have an EGR valve on it and it is not working properly (i.e. allowing too much exhaust gas in at idle), that could cause a bad idle. Could have a bad ground on the fuel pump also.
Top Bottom
Back
Forums
Menu