Search results

  1. 4

    Radiator Support Install Question

    Well for a shop it is no big deal, but to do it right will require you to do some fairly major surgery. It is not really a stress panel but I would want it welded in and painted so it will look correct. Dwayne
  2. 4

    Radiator Support Install Question

    If the rad support is just tweaked it is not worth replacing just remove the radiator and condenser and stand on the bottom of the support to move it back into position. I hav just had a light front end collision and the bottom of the support does very little, just move it back close and gently...
  3. 4

    synthetic oil....not a good idea with a blower?

    Gimme a break there is so much BS surrounding synthetic oil and what you cant run it in. If the motor is not leaking or burning oil running synthetic will change nothing other than an increase in economy/power and allow you to extend your oil change interval
  4. 4

    charge or pi?

    I second the above statement. I have a pair of PI cams I will sell you for $120 shipped. Dwayne
  5. 4

    need a new clutch but im on a budget

    Just stick with stock and don't abuse this one. There is no reason why it shouldn't last you 100,000 miles
  6. 4

    Idle way too high

    no that's Chevy starters and Ford IAC's get it right........ Dwayne
  7. 4

    1996 GT vs 2001GT

    canx
  8. 4

    still can't get rid of misfire!

    Not an obvious choice but how is the battery and alternator? Take it to a Walmart TLE they will test the system for free. I have seen this cause strange problems. Also remove the ground on the drivers side of the engine/chassis and give it a good clean, hell give every ground you can find a...
  9. 4

    96GT heads cam intake

    From the experience with regrind cams I saw everyone go through a couple years ago I will not even think about regrinds. I went with Comp Cams and everything is as quiet as stock with a nice lope and no issues. Dwayne
  10. 4

    NPI Head Milling

    just have the heads milled to resurface them, the compression jump for 10tho is .25. Porting these heads are from what I understand a very tricky buisness it is easy to do way more harm than good by removing material that should not be removed. I am very handy with a dremel and quite an...
  11. 4

    Brake noise....help!!!

    So where in England are you? I have spent 12 years at RAF Mildenhall. Anyway I would perform several back to back stops on a quiet road to put some heat into the rotors and clean off the pads. Depending on the age of the pads I would also look to see how much pad life remains, you may be on...
  12. 4

    Need some power...

    I would have suggested saving the money you wasted on minor bolt ons and put that towards the purchase of the blower, those little things have eaten $600 minimum that would have gained you little power and would have gone a long way to getting you the blower. Dwayne
  13. 4

    Header Replacement

    Royal pain in the ass. LT's give more gain but then require removal of 1 side to change clutch. Shorties help breathing up top, make it easier to change clutch but are still difficult to install, they do allow you to use your existing exhaust components. Dwayne
  14. 4

    Hood weight?

    pretty light really. I have installed mine by my self with no problems. They are composite. Dwayne
  15. 4

    x pipe that works with stock manifolds for a 98?

    I also have a pair of PI cams if needed. Dwayne
  16. 4

    How long are stock COPS good for?

    Not the only thing you can do. Clean the MAF/replace the air filter/run injector cleaner and spray injection cleaner into a vac port with the motor running like sea foam or I just use any spray carb/injection cleaner. Dwaynel
  17. 4

    How long are stock COPS good for?

    Just clean your COPS up with some wd40 and a nylon brush dry them and reinstall them using the silicone grease they should be just fine. Dwayne
  18. 4

    x pipe that works with stock manifolds for a 98?

    I have a Bassani OR X that I will sell to you for $120 shipped. Dwayne
  19. 4

    PUtting in My TB right now but have a problem

    oh yes and while we are on the topic of waste of time, the removal of slack achives nothing so long as the throttle opens fully as designed by ford. Others have bent parts by removing the slack and the throttle opens fully before the pedal hits the floor. They push harder and screw things up...
  20. 4

    Comp Cams installed, ticking noise, base circle problem?

    the spring change will require either the heads to come off/ shaved reinstalled or you can use air to keep the valves shut and the Ford special tool to remove/replace the keepers. I have believe it or not used soft rope stuck down the sparkplug hole, then gently rotate the crank so the piston...
Top Bottom
Back
Forums
Menu