Search results

  1. fords2fast4u

    Friends car has no power over 4000rpms

    yeah, the spout could be out? lol
  2. fords2fast4u

    Bend the frame?

    that's just it though, i don't think im anywhere close...
  3. fords2fast4u

    Bend the frame?

    i haven't measured them, but you can see them in the pics. I checked out the D&D's a second ago, but i think i'd rather get new/shorter struts before i replace the 200 dollar items.... jmo
  4. fords2fast4u

    Friends car has no power over 4000rpms

    ok, so it's wither timing or fuel... has he ever ran the car out of gas? does he have alot of miles? If either is true, the fuel pump may be weak and need replacing. Also check the cap/rotor. i had simular problems when my inline fuel pump had a bad power contact... it would run fine...
  5. fords2fast4u

    IS it true?

    you're going to have to be more specific...
  6. fords2fast4u

    Bend the frame?

    can i just get shorter front struts???
  7. fords2fast4u

    Bend the frame?

    i don't think anyone is going to be able to set it - that's why i'm wondering if anyone else has ever had this problem? :shrug: this really sucks because i can't drive my car until i get this fixed.. :(
  8. fords2fast4u

    Picture Thread...But Read Instructions Carefully!

    downsized quite a bit to fit, but here she is...
  9. fords2fast4u

    Bend the frame?

    i was thinking that i could shave the edge of the plates so that they could go a little but farther out, but even if i get it set - that still doesn't address the problem with the car... how could BBK springs, KYB shocks and Steeda C/C plates throw off the alignment this far? There has to be...
  10. fords2fast4u

    Bend the frame?

    measurments... Toe 0.00"/0.01" (both green w/ a total toe of 0.01") Caster 2.9*/2.9* (both green) Camber -2.1*/-1.8* (both red) i said earlier that one of the cambers was in the red too, but that was the start alirgnment, not the finished state. Anyhow, it's changed from these numbers...
  11. fords2fast4u

    Bend the frame?

    as you can clearly see, the wheel is not on the pavement straight (the top is in by about an inch +) and the plates are against the fender...
  12. fords2fast4u

    Bend the frame?

    more...
  13. fords2fast4u

    Bend the frame?

    Here are some pics...
  14. fords2fast4u

    Bend the frame?

    the plates are hitting the fenders.. :(
  15. fords2fast4u

    Anyone Have Pics of 6AL Placement????

    i needed one after i installed some crazy cam that is long gone now and for the blower. I mounted it on the radiator support right where the letters "mustang" used to be, i cut the plastic to fit around it and built a bracket..
  16. fords2fast4u

    Bend the frame?

    yeah, sears isn't the best place in the world - but i had taken it to them before and they charged me for an alignment even though they couldn't set it... so they told me that when i got the plates i could take it to any sears and they would set it for free, as per the 6 months warranty. That...
  17. fords2fast4u

    Bend the frame?

    Ttt...
  18. fords2fast4u

    Corbeau

    i know what you're talking about - and im not a heavy guy.. 6'1" - 190 lbs and here in NJ where the parking spaces are small and the stangs doors are long, it sucks quite frankly - my seats have the leather on the sides and when I get in and out - i try extra hard not to put pressure on them...
  19. fords2fast4u

    Corbeau

    well i was thinking of posting a pic, but it's the same thing as CAR NUT... (nice seats man) everyone who rides in my car compliments me on the seats, but im the one that has to crawl in and out of them every day - and if a car is parked close to you, and you can't open the door all of the...
  20. fords2fast4u

    Bend the frame?

    slytherin - i did take it to a shop - Sears, and they have a really nice computer setup with a printout and green and red numbers. The printout shows that they set the tow (or thats what they told me) and the camber was border line (one red, the other barely in the green) and the camber was no...
Top Bottom
Back
Forums
Menu