Search results

  1. D

    Engine wont stay running

    check all vaccum hoses for cuts/rips as well as tight connections. then go to the IAC valve. after that my next guess would have been fuel filter, but you just replaced it....
  2. D

    Replaced A/C clutch, but it wont engage

    i dont know what you mean by "which terminals". i would try to apply power directly to the compressor though with a power probe. or at least use a test light to see if you have power going to the compressor. my guess is you may not have power since you just replaced the clutch (i asssume coil...
  3. D

    I'm a COMPLETE noob....

    i didnt read evey single reply, but did you make sure your intake isnt cracked as well?
  4. D

    Replaced A/C clutch, but it wont engage

    did you measure the clearance of the clutch with feeler guages? theres a specific gap you need to enforce follow when you install those.
  5. D

    Lemme see ya grill

    i dont know how many bars. its not hard to clean at all, i just spray it with water and run a soapy sponge over it. its stainless stell i think, so it hasnt tarnished at all over the past 4 years
  6. D

    sound system

    $1000? lol, i'll do it for $500 :D
  7. D

    finally have some numbers... 1/4

    nice times, thats ~ what i ran with 4.10s and an X pipe
  8. D

    Help me understand gearing (total newbie to RWD and domestics).

    double post
  9. D

    Help me understand gearing (total newbie to RWD and domestics).

    haha. thanks. thats what i get for not re reading my posts
  10. D

    What's wrong with my ride!?

    how many miles? im thinkin theres just not a huge demand for an 8 year old mustang :shrug:
  11. D

    Steering Wheel Vibration Need Help

    unless the rotors have been resurfaced a couple times previously, he shouldnt have any problems at all resurfacing them. the worst warpage ive ever seen took only 3 cuts, at .002", which is only .006" total cutting. most manufacturers set pretty lenient specs for the rotors too. Acura and...
  12. D

    Steering Wheel Vibration Need Help

    i agree with this guy :D
  13. D

    Brake question

    i agree with twogts, unless the master was visually leaking (you can see residue on the booster, right under the MC), i wouldnt have replaced it. now, im not experienced with Ford's Hydro booster, but maybe its at fault. hopefully Mike will chime in here.
  14. D

    Help me understand gearing (total newbie to RWD and domestics).

    stock gearing ratio on 99-04 GTs is 3.27:1 that is the relationship between the rear wheels and driveshaft. so for every 1 rotation of the rear wheels, the driveshaft will spin 3.27 times. so changing your gears for, say, 4.10:1 means that for every revolution of your rear wheels, your...
  15. D

    Lemme see ya grill

    old pic. i just realized i dont have any recent pics of the front end, but its basically the same still, save for some 02+ smoked headlights
  16. D

    My mustang is bucking while driving

    no, start with the obvious. you have a code for a fuel tank pressure switch. replace that
  17. D

    "Go" pedal stuck every now and then?

    ^^^^ sorry, im posting from work and my co-workers like to play pranks on each other. for the record, i like tang
  18. D

    "Go" pedal stuck every now and then?

    bingo. i would clean the TB first. crap gets built up around the edge of the butterfly valve in the TB and sticks. thats a big safety issue. if its not the carpet that is...
  19. D

    "Go" pedal stuck every now and then?

    .
  20. D

    My mustang is bucking while driving

    i would start with the obvious and go from there. first replace your fuel tank pressure sensor. im not sure on fords (maybe a ford tech can chime in) but on Hondas you usually have to replace the bypass solenoid, 2 way check valve, and canister vent shut valve. after that, if its still...
Top Bottom
Back
Forums
Menu