Search results

  1. Last5.0

    Oil Leak from Distributor help?

    Yes, there is an O-ring seal on the distributor that seats to the block. You have to pull the distributor fully out to change it.
  2. Last5.0

    Stud vs pedestal rockers?

    Yup what Kurt said. I prefer stud mount better just because it's so much more easier to adjust, but you need more clearance inside the valve cover to clear the poly locks.
  3. Last5.0

    99-04 Dual piston calipers on a 94?

    Remove the calipers with the brackets from the spindles. You should be able to get the '99-04 calipers with brackets from the parts store along with the lines and they are a direct bolt-on with the exception of the bit of grinding on the spindle bosses. Make sure you get the lines for '99-04...
  4. Last5.0

    99-04 Dual piston calipers on a 94?

    Here's a link to some swap info and pics Ford Mustang: Mustang Tech: Brakes: Low Budget PBR brake upgrade Also a pic of where the spindle needs to be ground...
  5. Last5.0

    99-04 Dual piston calipers on a 94?

    I've been running stock '99-04 PBR calipers for over 5 years and have never had any problems. I got them cheap, like $50 with pads, rotors, soft lines and banjo bolts. The rotors are the same as stock ones on my '95 GT and the grinding is just a little bit on the back of the spindle so that...
  6. Last5.0

    A Must Have!

    Yeah it's actually cheaper to buy a whole new fixture than piecing a ballast and sockets together on a 2x4 :D Does the original one 4Jenna posted have the bulb inside a plastic case or anything protective? When these bulbs break they shatter glass everywhere. They make clear protective...
  7. Last5.0

    A Must Have!

    Aww man, I liked your car (almost twinkies with mine) untill I just noticed you have the two tone black/grey interior :p
  8. Last5.0

    A Must Have!

    If my 1.21 Gigawatts of fluorescent overhead garage lighting doesn't cut the mustard I pull out my handy Craftsman fluorescent work light to light up those dark nook and cranny areas Or my cheap rechargable LED worklight ($25 HF special) :D
  9. Last5.0

    A Must Have!

    Lol, that's funny that your neighbor across the road asked you to turn the light off. The front of my garage sits 110 feet back from the street so I've never had that problem
  10. Last5.0

    Fitting for Catch Can?

    You want bigger than 1/4" lines going to the catch can. 3/8" minimum, 1/2" - 5/8" preffered. Most catch cans have a 1/2" NPT thread on them for a fitting. 1/4" hose uses a size -4AN. You can get something like a 1/2"NPT to -4AN fitting that screws into the can then just put a -4AN...
  11. Last5.0

    A Must Have!

    Nice light, but not for me though. I have tons of lighting in my garage...eight 4' 4 bulb fluorescent fixtures....40w per bulb...1280watts total.....lol Garage is 30'x35' with 10' ceilings so it's not too blinding of a light but just right
  12. Last5.0

    94 cobra...water pump studs???

    No studs are needed on the '94/5 GT water pumps. Only on Cobra and only for the factory oil cooler hose mounting tabs.
  13. Last5.0

    I was being a doofus and...

    Yeah, you're a doofus.....should have just had one of the neighborhood kids help you by holding the wire :D
  14. Last5.0

    went to roush nascar team and saw this

    Yup, built for a Ford/Chevy challenge like said above. I still have the old issues of MMFF and 5.0 Mustang that have full featured articles about it.
  15. Last5.0

    Suspension Which Isolators?

    Yup, the wheel size may be bigger but the overall diameter (tire height) is usually about the same. If it wasn't you would have to correct the speedo.
  16. Last5.0

    Catch Can or Air Oil Separator???

    It's pretty much common knowledge that when running breathers and no PCV that the oil gets contaminated sooner and requires more frequent changing. With a breather or catch can (which is just a remote breather system) the oil vapor exits the engine by rising to the top and through the...
  17. Last5.0

    what a difference!

    Good to know if I ever do a fox TB swap
  18. Last5.0

    How to solve headlight switch overheating issue

    Yup, been running the vert harness fog light mod since the mid-late '90s and no problems. My car hasn't been a daily driver since about '02 though.
  19. Last5.0

    How to solve headlight switch overheating issue

    I've never had this problem and always ran fogs with the tinted headlights. The fogs are usually on a relay so the current for them isn't going through the headlight switch. How are your fogs wired up? Just splice power at the switch from the convertible top harness. Easy one wire mod with...
  20. Last5.0

    what a difference!

    Maybe, I wouldn't know. It's been a long long time (10+ years) since I've had a stock intake tubing setup. I'd think some kind of combination of a Fox intake tube and 94/5 fender mount would work. I know with a blower and fox throttle body swap you can just clock the volute a bit over more...
Top Bottom
Back
Forums
Menu