Search results

  1. F

    BBK SSI intake?

    Its hard to do a search for things when the search feature don't recognize anything under 4 characters long :P
  2. F

    AOD problems

    When you installed the TC, after you bolted the trans back up to the motor could you still wiggle the TC back and forth a little before you tightened the TC to flexplate bolts? Not quite sure what you could screw up just taking the TC out that would make it not kick into 2nd unless it wasn't...
  3. F

    AOD problems

    Are you sure the TV cable is adjusted correctly? Almost sounds like your line pressure is to low which would cause the way late upshifts and delay poppin into gear. It worked fine before the TC swap and then started doing this when you installed the new one?
  4. F

    AOD GENERAL ? THREAD

    If you can find some lines the right length just get a tubing bender so you don't kink anything and give her hell :). I sure feel like an oddman out lol I love my auto. Just out of curiosity is there a shift kit or anything installed? Am currently running mine w/ a 2.8k stall and a transgo...
  5. F

    1996 - 2003 dash, int in Fox body

    Installing a pushbutton for a door popper is actually a pretty good idea imo. I already shaved my door handles on the outside and had poppers put in that work off my alarm remote so probably why it sounds like such a good idea to me :D but a pushbutton on the inside to trip the popper sounds...
  6. F

    AOD trouble, not shifting to overdrive

    AODs are fun :P but yes can be a pain, after you check out the TV cable like ron said and if it all looks fine (there is a small grommet that the TV cable goes into that is rubber and disintegrates over time, most people use the brass replacement grommets) theres probably a good chance you...
  7. F

    Question about roller blocks

    I don't understand how, if the measurement on the roller and flat tappet lifters is the same from bottom of lifter to top of oil channel, there can be any variation on where they would put they oil galley on ANY block that would use these lifters. If the oil channel on the lifter was going to...
  8. F

    Question about roller blocks

    Nope I wouldn't see any problem with any kind of oiling issues as long as you could get those dogbones secured well enough. Can't really see what these people saying you would have issues are talking about though maybe they haven't actually LOOKED at the parts. :) And to answer your question...
  9. F

    Oil Pan Gasket

    Best thing to do is unhook the 2 motor mounts and the trans mount and jack the engine up until you hit firewall (do be careful not to squish things :)) be sure you have the car as high as you can safely manage on jackstands cause you will need the room. You won't be able to get the pan...
  10. F

    Can you cook a thermostat?

    Well the new one works fine and doesn't spike my temp before it drops (when I said spike it would kick the needle all the way up top to 270 deg) it either got hosed from the heat or the sloshing when I had the air bubble from refilling or from the initial upper rad hose blowout that started the...
  11. F

    Can you cook a thermostat?

    I recently overheated my car a little much when I had a air bubble in the system and ever since then the temp needle has to spike before the thermostat opens and the temp drops back down to mid range where its supposed to be. This always happen when you get em to hot? Was changing it today...
  12. F

    Horn issue

    LoL! Gotcha! :D
  13. F

    Horn issue

    I had this happen to my old stand as well and found out what was wrong was not all that hard to fix. When I pulled my horn button apart there are 2 copper disks inside with foam in between them so they don't contact, when you press on the horn it smashes the foam and presses the 2 plates...
  14. F

    my injectors

    Sounds like there may be a short to ground somewhere? .. If I'm not mistaken the injectors are fed power at all times and pulse when the ground is completed.
  15. F

    Question about roller blocks

    Nope oil channel is in the same location on both just the taller bores on the roller block like you said. I just went and checked for you even, the distance between the bottom of a flat tappet lifter and the top of the oil channel is the same measurement as from the bottom of the roller tip to...
  16. F

    AOD Torque Converters

    Weird, curious as to what setup you have (what brand input shaft/TC?) just trying to figure out how it would hit OD ratio with no lockup.
  17. F

    AOD Torque Converters

    Pretty sure theres only a couple companies that actually make the hardened input shafts just lot of people carry them. I thinkin the 300M alloy shafts you can't go wrong with, haven't had much experience with the 4340 alloy shafts but have "heard" they are the weaker ones.
  18. F

    Back from the dyno!! Very happy **PICS & VIDS**

    Wow 156k miles on the motor and those kind of numbers are great :D looks like you take good care of her!
  19. F

    AOD Torque Converters

    The intermediate/direct input shaft IS the lockup feature .. it splines directly into the back housing of the TC and is ALWAYS 1:1 with the motor .. this is the weak link because its a 3/4 diameter shaft and is eliminated with non lockup converters because when you bang into 3rd gear at WOT and...
  20. F

    Replacing Oil Pan

    Have no idea how you'd do it in the car (replace the pan totally that is) both times I've had to change an oil pump in the car I had it jacked up until the bellhousing hit the firewall and there is no way I could have gotten the pan totally out, so I'm with the other guys :) just jack it up and...
Top Bottom
Back
Forums
Menu