Search results

  1. larrym1961

    Cel Light How To Get Rid Of After Catted X-pipe Install?

    I think after cat sensors came on 96 and later OBD II equipped vehicles.
  2. larrym1961

    What Optima Battery Part Number Do I Need?

    I went into a NAPA Auto Parts store one time to buy an Optima red top battery for my Mustang. The salesman there suggested their NAPA Gold battery over the much more expensive Optima. He said I would be much happier with the NAPA one.
  3. larrym1961

    Rear Gt Hatch

    The LX hatch would several extra holes in it for mounting the LX spoiler that would probably need plugged if You plan on using the GT spoiler.
  4. larrym1961

    Cjponyparts Shipping

    That works the same way for items bought on Ebay also.
  5. larrym1961

    No Power At Wot, Revs Fine In Neutral

    One time my car would rev just fine in neutral but under load acted like a dog. The hot wire of the mass air meter was dirty, partly resulting from use of a K&N air filter. After I cleaned the hotwire of the mass air meter it was like a total different car, like I added 50 extra horsepower. So I...
  6. larrym1961

    Runs 10-15 Min Then Stalls

    I have an MSD Pro Billet Distributor and the MSD TFI went to crap within a month of it being installed. Car would backfire and die and would restart after the TFI cooled down. I replaced it with a Motorcraft TFI and have been problem free since.
  7. larrym1961

    What Is This Hole On The Top Rear Of The Block?

  8. larrym1961

    Slow To Drop Timing Advance

    Did volt test on 02's. .2V @ idle on both. I did find a small vacuum leak. Vacuum hose from AM solenoid to smog pump was sitting against header and cooked. Removed the burned vacuum hose and capped it off @ AMS. Reset ECM and took for a drive. Ran another code test and now I get the desired code...
  9. larrym1961

    Slow To Drop Timing Advance

    Just took another vacuum test and as confirmed 13HG's @ idle.
  10. larrym1961

    Slow To Drop Timing Advance

    I don't think I have ever had more than 13HG's of vacuum @ idle since I installed my new motor in 2005. Probably time for a smoke test to check for vacuum leaks. And also if Joe puts up the 02 sensor check I will go thru that also. With the new injector harness, I grounded 02 ground wire to...
  11. larrym1961

    Slow To Drop Timing Advance

    Well I went out and ran codes again and I am getting the dreaded codes 41 and 91
  12. larrym1961

    Slow To Drop Timing Advance

    I could not find any vaccum leaks. (not to say I could be missing something) 10 pin connectors are clean and good. I installed a new Ron Francis Injector Wiring Harness not to long ago. It is just odd that with the IAC unplugged and also the spout disconnected the idle does not hang but hangs...
  13. larrym1961

    Slow To Drop Timing Advance

    I have a E303 cam and I have adjusted the screw w/ IAC and spout connector unplugged to set idle to about 750 to 800 RPM. Idle will still hang after the throttle is stabbed with no IAC but will not with the spout unplugged.
  14. larrym1961

    Slow To Drop Timing Advance

    No codes. Base idle is set at 800 RPM. Base timing set @ 10 degrees. TPS @ .98.
  15. larrym1961

    Slow To Drop Timing Advance

    I have had an issue for a while of that annoying "hanging idle" after stabbing the throttle and letting off the gas. It hangs @ about 1500 RPM for about 5 to 7 seconds then drops back to normal idle. Doing some experimenting, first I unplugged the IAC then stabbed throttle, the idle still hung...
  16. larrym1961

    Contour Fan Wiring- Dual Speed Knowledge

    The fan hot wires are wired directly to the VSC. The VSC has a 30 AMP fuse on it.
  17. larrym1961

    Contour Fan Wiring- Dual Speed Knowledge

    I have my dual Contour Fans wired to a Flex-A-Lite Variable Speed Controller and they work great.
  18. larrym1961

    Tfi Manual Or Auto?

    Thanks for the info Joe, I had done some research and found Tom Moss's thread on this subject. When I bought my extra (grey) Motorcraft TFI about 10 years ago I did not ever remember the parts Man @ Ford asking if it was for a Manual or Auto trans car and mine has worked just fine with both...
  19. larrym1961

    Tfi Manual Or Auto?

    What is the difference between a TFI for 5.0 Mustang w/ Manual or Automatic trans if any? I have seen them listed for both types of transmissions.
  20. larrym1961

    Pin 30 Question?

    Once again thanks for the info. I have entertained the Idea of switching to a 89 and later harness also. But I think for now I will stay with what I have and live with the short "hanging Idle". I have done it since 2002 when I made the trans swap. It's more worth it to me to have that little...
Top Bottom
Back
Forums
Menu