Search results

  1. 90silverstang

    Hood Hinge to firewall Rust, How to repair?

    No comments?
  2. 90silverstang

    Hood Hinge to firewall Rust, How to repair?

    I ordered a Mig welder today for this project. What do you think about this welder? FREE SHIPPING — Hobart Handler 140 MIG Welder — 115 Volt, 140 Amp, Model# 500500 | Wirefeed Welders | Northern Tool + Equipment
  3. 90silverstang

    Front End/Engine Bay Detailing Project

    Welder I just purchased a Mig Welder today check out this link and tell me what you think. FREE SHIPPING — Hobart Handler 140 MIG Welder — 115 Volt, 140 Amp, Model# 500500 | Wirefeed Welders | Northern Tool + Equipment
  4. 90silverstang

    Hood Hinge to firewall Rust, How to repair?

    How would you body guys repair this? I want to learn how to weld. I saw a mig welder at harbor freight. would this get the job done? any suggestions? Is this to small? ony using on sheet metal and for holes in engine bay. - Harbor Freight Tools - Quality Tools at the Lowest Prices
  5. 90silverstang

    Front End/Engine Bay Detailing Project

    Don't know what happened to the previous pics so here they ara again Sorry haven't replied been busy and went to Las Vegas on Vaca. Engine bay is white because thats the original color of the car. Thats why I'm detailing the engine bay now. Here are...
  6. 90silverstang

    Front End/Engine Bay Detailing Project

    Where did you mount the relay and how did you run the wires on the drivers side? They go through the firewall and then what? Did you have to undo the wires from the black shield tubing and then route the wires to get the wires to be more flexible? On the passenger side where did you mount...
  7. 90silverstang

    Front End/Engine Bay Detailing Project

    I Knew these questions were going to be asked about filling the holes and Hiding the wires. My question is what holes do you fill in and what hole don't you fill in? You need some of the holes for mounting things? As for hiding the wires how do you route them? are there length issues. Where do...
  8. 90silverstang

    Front End/Engine Bay Detailing Project

    I started he project and I am at the point of dropping the K member. Made a Dolly and attached to the bumper receiver I dropped the control arms down to relieve the spring tension, but I didn't see the reason to pop them all the way out because I am removing the K...
  9. 90silverstang

    Stock K Member Alignment

    How do you square up a stock K member? Which points are used for the plumb bob on the k member and by the rear lower control arms??
  10. 90silverstang

    Throw Out Bearing, Bearing retainer, Clutch Fork, Pivet Stud

    what about the throwout release bearing. there at Napa, Autozone, LRS are there bearings that are better than others??
  11. 90silverstang

    New Mounts Motor and TRanny...trans sits too high

    I have that problem to. I purhased a Autozone transmission mount-- just the regular rubber kind and it made the trans sit to high. I was thinking of replacing it with a ford stock mount.
  12. 90silverstang

    T5 Rebuild or not

    OK, good enough
  13. 90silverstang

    T5 Rebuild or not

    I have pulled the engine with the t5, transmission shifts fine but should I rebuild it since it is out, I am rebuilding the clutch and related components. I was planning to replace the tail shaft bushing and seal. Also changing the speedo gears so the speedometer is accurate w/ the 373'S...
  14. 90silverstang

    Throw Out Bearing, Bearing retainer, Clutch Fork, Pivet Stud

    My question is-- are there certain brands for the clutch fork, bearing retainer, Pivit Stud and throw out bearing that are better than others. What brands are the best. Is NAPA or Autozone for these parts OK? What should I stay away from? What brand makes a stronger clutch fork for the T5 and...
  15. 90silverstang

    Pulled the Engine --- Thanks!!

    I did not post a thread for help but I searched the 5.0 tech forum on pulling the engine, because I found the info that I needed. I wanted to thank everyone who shared there knowledge and experience because it helped me out on what to be careful of, safety, tips and pulling the engine with the...
  16. 90silverstang

    Has anyone done business with T and L Engine Development in NC

    T and L website Stroker Engines_Crate Motors_Stroker Kits_NC Custom Stroker Engines-TandLEngine Development Stanfield, NC I have read some good things and some bad things. One of the owners told me that they have had problems getting engines out the door but mostly on engines that require...
  17. 90silverstang

    Has anyone done business with T and L Engine Development in NC

    I'm considering purchasing a 347 crate engine from them. Has anyone purchased a crate motor from them?
  18. 90silverstang

    Has anyone done business with T and L Engine Development in NC

    I'm considering buying a 347 Crate engine. Has anyone purchased a crate engine from them?
  19. 90silverstang

    Exhaust used by Convertible Owners?

    I have Headman shorty headers to 2.5" offroad H pipe to 2.5" Flowmaster American Thunder Catbacks on a 90gt vert. It is loud but it sounds awesome. Good luck.
  20. 90silverstang

    Will the performer lower fit GT40X Heads?

    As the title says.
Top Bottom
Back
Forums
Menu