Search results

  1. K.C.90gt

    What are the steps to installing new guages??

    Its not hard to do, all you really have to do is run wires from the engine bay to the interior, replace the stock sending unit with the supplied sending unit (electric gauges), and connect + and - and a positive on/off to tell the gauges when to light up or not (usually hook up to headlight...
  2. K.C.90gt

    Clutch cable keeps snapping - HELP!

    I just had my cable do the same thing, it frayed and almost snapped right before it goes into the bellhousing. I'm almost positive it was caused by being too close to the headers because the black plastic covering looked somewhat melted. Check the exhaust and make sure there is some room...
  3. K.C.90gt

    What was it like when you raced for the first time?

    My first time my adrenaline was pumping big time on my way up to run. I was nervous too palms sweety, knees shaky, but once the light turns green and you punch the gas, the nervousness goes away and its all smiles after that. I missed a few shifts every once in a while too the first time to...
  4. K.C.90gt

    Definitive Answer On Spring Installation?

    yes that's the way it should be.
  5. K.C.90gt

    My MSD needs repair..

    thanks! Whats so good about the crane ignition anyway?
  6. K.C.90gt

    Definitive Answer On Spring Installation?

    hehe hey again 89MustangGX, I did the springs when I did the control arms and in the steeda springs instructions it says to face the end of the pigtail towards the drivers side of the car like everyone else said. I don't know if I would install it any other way because it might not function...
  7. K.C.90gt

    Anyone have as much trouble installing spherical bearings as I did?

    well.. im not sure on how your control arms are setup but the ones I got were only spherical on the axle side of them. They had a sphere in the center of it that had two metal hallow cylinders on each side of the sphere that you could slide right out. I put the antiseize on both ends of these...
  8. K.C.90gt

    Anyone have as much trouble installing spherical bearings as I did?

    these are on uppers? I wouldn't go through the trouble personally just to put some antiseize on them, They should be just fine. :nice:
  9. K.C.90gt

    DOOR LOCK ACTUATORS..

    When you push the unlock or lock button it should make some sort of noise if the button is working correctly. Either way you still should be able to unlock the door with the key or pulling on the inside door handle. If the button doesn't work than it could be dirty contacts or a fuse or a...
  10. K.C.90gt

    My MSD needs repair..

    My wires melted on my MSD 6AL from my blower touching it, wasn't touching it when I installed it, motor must have moved a little after I dropped it in. But anyways it grounded out the wires and melted the main wire all along the MSD wire harness. I would just fix it myself but its melted all...
  11. K.C.90gt

    Anyone have as much trouble installing spherical bearings as I did?

    It said to use antiseize on the ends of the bushings, the part that contacts the axle's metal control arm housing, not inside the boltholes. It helps to slide them in easier when installing and also prevents them from wearing faster and getting stuck in there over time.
  12. K.C.90gt

    DOOR LOCK ACTUATORS..

    well if the button works on the drivers door or if you hear it activating the actuators than no it wont do nothing because the button works, I didn't know if your button works or not but I was just giving some more possibilities of what it could be. But more than likely its a frozen actuator if...
  13. K.C.90gt

    DOOR LOCK ACTUATORS..

    yea, you should be able to remove the panel with the door closed. my lock button didn't work at one point and I took the cover off of the lock buttons and sprayed some wd-40 underneath the button by the trigger and worked it back and forth and it cleaned the contacts and started working, so...
  14. K.C.90gt

    newbie wants '89-'92 Stang...

    My brother had a 94 z28 which I rode in a lot and drove and I didn't like the way it sits and how hard it is to work on. In the camaro it feels like your laying on the floor looking out of a bubble warped windshield and huge dash that blocks a lot of your view. The backseat is horrible in the...
  15. K.C.90gt

    DOOR LOCK ACTUATORS..

    when you say manual locks do you mean you dont have a lock/unlock button for power locks? because if you have actuators then they are power locks. Anyway if you do have power locks then I can offer some help. This happened on my 93 ford tempo, it uses the same door lock actuators. My door...
  16. K.C.90gt

    Anyone have as much trouble installing spherical bearings as I did?

    i dont think it should be that big of deal... but If I remember correctly it said in the instructions to use antiseize or some type of grease on the end of the bushings so you might want to do that but If you don't it probably wouldn't matter too much, might just get stuck in there over time easier.
  17. K.C.90gt

    Anyone have as much trouble installing spherical bearings as I did?

    What control arms did you put in? I used Pro3i Spherical lowers and It was a little PITA. It was a pretty tight fit but with some antiseize and a rubber hammer I got it someone into place then pounded a bolt through it finish it up. The hardest part was trying to line up the holes to get the...
  18. K.C.90gt

    Could clutch cable be my problem?

    I too also think it is your clutch cable. I was having similar issues as you and the more I drove it the harder it was to enage a gear, it got to the point to where I could not even engage a gear. I looked under the car where the cable connects to the bellhousing and the stock cable was...
  19. K.C.90gt

    Thinking of painting my manifold.

    I like the paint scheme you have in that picture with leaving the middle unpainted. But I thought I would add a suggestion, you should paint the edelbrock lettering black after your done to make it look even better. I did the lettering on my trickflow intake with some touchup paint and it...
  20. K.C.90gt

    Detroit Area Mustang guys

    I'll be out cruising gratiot or telegraph after weather gets better and I get mine dyno tuned from someone around here probably alternative auto, I talked to Lidio and he said he would take care of me, I went to a dyno day there at the end of last year but got their too late. Has anyone got...
Top Bottom
Back
Forums
Menu