Search results

  1. woodsnake

    Fmx To T5 Swap Parts List Help

    good info here, 7173MUSTANGS.com clutch pedal here Modern Driveline, Inc. - pedals
  2. woodsnake

    289 Cam Failure

    I have had 2 Edelbrock Performer RPM cams wipe a lobe, or lobes.. You say you built the engine 7 years ago, but now have a failure? Did the engine sit for that long, before you ran it? My failures turned out to be push rod related/coil binding. Did you use a custom push rod? I agree it is...
  3. woodsnake

    How Much Is A 1970 Boss 302 Engine Worth?

    This looks like one that was just listed on Ebay a week or two ago... Original 1970 Ford Mustang Boss 302 Engine Doze 6015 C | eBay
  4. woodsnake

    How Much Is A 1970 Boss 302 Engine Worth?

    a hundred dollars, says this engine is just another 302...real Boss 302's are very expensive......Got pictures?
  5. woodsnake

    Fitting An 18x8 Wheels On A 68 Mustang

    Have a read here.. Mustang Photo Archive
  6. woodsnake

    65 289 C4 Will Not Start

    What electronic ignition do you have?
  7. woodsnake

    Le Mans Bowl Fittings

    Thanks! I thought I was on my way back over seas, and have now been living in NY for about a year. Everything I own, however is in Colorado...Can't work on the projects so not much to report on the boards that I do visit...
  8. woodsnake

    Le Mans Bowl Fittings

    I recently acquired a 4118 Holley, that came with the Lemans fuel bowls. However, the previous owner didn't use the correct fuel line. The steel line is the easy part. I would like to find out if there is a common brass solution? Specifically sizes that I can order online? I don't have easy...
  9. woodsnake

    Power Brakes With Manual Tranny?

    I don't think it matters, really. As long as you have the dual MC, and proportioning valve, you should be good to go.
  10. woodsnake

    Dissapointing Results - Have I Missed Something?

    I'm sure they checked it, but I didn't see the numbers...I also think that the carb is too small, and you might be happier with a performer RPM intake and a 650 CFM. What size exhaust pipe are you using? 2 inch? 2 1/4?
  11. woodsnake

    Dissapointing Results - Have I Missed Something?

    Do you know where your timing is at? I would start with the basics...
  12. woodsnake

    Engine Options (socal)

    I would look at swapping the trick flow heads, for another aftermarket head. A roller block will give you a lot more options when it comes to camshaft selection.
  13. woodsnake

    New 65 Mustang, Help With Making It A Daily Driver! A

    Regarding the stalling, with the heat on, what is your idle speed?
  14. woodsnake

    Dizzy Making Me Dizzy

    Was it it this kit? http://www.summitracing.com/parts/edl-2027 If you didn't measure for push rods, that absolutely can be a problem. Also, keep in mind that you now have guide plates, and that requires a hardened push rod.
  15. woodsnake

    Dizzy Making Me Dizzy

    How much camshaft did you install? Did you measure for push rods? Did you use roller rockers, or did you use the stock, non adjustable rocker arms?
  16. woodsnake

    A 5.0 Block With Toploader Trans-in A 67

    I will not recommend Trick Flow heads. I bought a pair several years ago, before I knew as much, as I know now. (Obviously) In 2005, I got a pair that are good for the shorter lift cam: http://www.summitracing.com/parts/tfs-51400002-m61/all In 2012, I finally got around to getting the engine...
  17. woodsnake

    Re-gear Vs Overdrive

    I have a 3.50 gear in my 68, with a T-5 trans. I also have the Edelbrock performer RPM cam in that engine. (.496/.520 lift) I would base the rear gear at least as much around the cam, as the desire for highway mileage. My engine pulls very well, but I would be happier with the performance with a...
  18. woodsnake

    Is This Carb Too Much For My Setup?

    I'm going to guess that your carb is no larger than a 600 CFM, and so no, it isn't too big for the 289. Are you talking about the aluminum tag that bolts on to the carb? How long has the car sat with out being run? Here is a link, that may help you identify your carburetor...
  19. woodsnake

    Engine 69 351w Roller Cam Conversion

    You realize you still have to measure for correct push rod length, right? Also, what heads are you using?
  20. woodsnake

    Made my own T5 shift stick

    If it is copy-able, I would be interested in a copy!
Top Bottom
Back
Forums
Menu