Search results

  1. MineralgreyGT01

    Help with LCA install

    The suggestion for PB blaster is a good one, you can get it at Wal-Mart and so is putting a little pre-load on it to take some weight off the bolt. Now this may seem kinda stupid to ask, but are you sure you were loosening, not tightening? The old righty-tighty lefty-loosy thing? A 1 foot...
  2. MineralgreyGT01

    Factory mid piep removal ?'s

    Have to remember how very little room there is up by the passenger flange, but heck any suggestions may work.
  3. MineralgreyGT01

    Factory mid piep removal ?'s

    3 suggestions: 1) Heat the nut with a torch , then hammer the next size smaller socket on there (14mm?) and try that. 2) Try and refile some flats back on and try next smaller socket 3) Try and double nut the stud out then rescrew it back in. Oh and lots and lots of PB Blaster...
  4. MineralgreyGT01

    Max power potential of the 05 GT?

    Well first thing (like when the 4.6 first came out) is aftermarket parts people will need to get their hands on them to figure out what they are working with. Then they have to figure out how to get around the drive by wire system. You can't just bolt a power adder on upstream of it because it...
  5. MineralgreyGT01

    03 GT Coil-Spring Install Help

    Even though I don't like Mustang World too much, they have a good write up. http://www.mustangworld.com/ourpics/fcar/steedaspring1.htm
  6. MineralgreyGT01

    HELP! started up car after headswap!!! oil pressure low?!?!

    Did you block off the oil port on the backside of the heads?
  7. MineralgreyGT01

    Can I put mils on after my off road H install?

    You can put them on after you put your pipe on but you will get a SES light at some time (usually after your second long drive or 500 miles). Most people just put them on at the same time since they have the car jacked up anyway.
  8. MineralgreyGT01

    Where to get IUP console trim peices.

    The Mach 1 bezel (inside piece around the gage face) is silver not black. But you are right it is not part of the IUP, just if you are going for the look.
  9. MineralgreyGT01

    Where to get IUP console trim peices.

    These are what we have for the Mach 1 IUP. I don't know if it is the same but probably is... Accelerator Pedal - 3R3Z-9725-AA - $34.04 Brake Pedal w/lever - 3R3Z-2455-DB - Obsolete Brake Pedal Pad - 3R3Z-2457-BA - $41.17 Clutch Pedal - 3R3Z-7519-AC - $54.48 4-Way Headrests -...
  10. MineralgreyGT01

    Exhaust on my '04 GT

    Yup something is different :) The 04 midpipe is different. Still has 4 cats but the O2 sensor location has changed and supposedly the amount/type of catalyst is different.
  11. MineralgreyGT01

    insurance for a mach 1

    I am 35, I pay $56 a month for full coverage, $250 comp $500 collision and I have it listed as a 'Pleasure Vehicle'. I have multi car coverage so this also helps. This is thru State Farm BTW.
  12. MineralgreyGT01

    NEED HELP FAST!

    Get a set of these from Napa. 600-1819 stud and nut kit. I think it is 5 bucks or so.
  13. MineralgreyGT01

    2003 Mach 1 Exhaust

    Heres 2 websites for you that cater to Mach 1's www.mach1registry.com www.mach-1.org you will be able to find a lot of answers to your questions there.
  14. MineralgreyGT01

    High pitch sound from back?

    Definately the fuel pump. Some are louder than others.
  15. MineralgreyGT01

    96GT has a whine sound

    It whining for some PI heads :) Sounds to me like some belt slippage or maybe the alternator starting to go :(.
  16. MineralgreyGT01

    So what are these things made of anyway?

    My guess: The hood and is fiberglass with a metal support frame. The 1/4 and doors are metal. We should make this a poll :rlaugh:
  17. MineralgreyGT01

    Help with Brake Issue!!!

    Your calipers are probably frozen in the rear. Have someone watch them when you apply the brakes. You can try exercising them with the parking brake. Good luck.
  18. MineralgreyGT01

    UPR x pipe and Magnaflow

    Check your rods that attach your tips. The ends of the rods are probably tapping against your tips. One fix is to realign your tips so the rod does not come in contact or cut the rod short.
  19. MineralgreyGT01

    2 SES codes I can't get rid of, and now 1 new one, please help!

    The P0455 is a leak back in your fuel tank vacuum sensing system. You can try reseating or replacing your gas cap. See if your gas cap hisses still when you put gas in it. If that is not it try looking at the sensor back by the tank. I believe it is external to the tank. I don't know where...
  20. MineralgreyGT01

    MIL Elimanator ???

    Just the back ones. Do NOT do the front ones, that would be real bad for drivability :)
Top Bottom
Back
Forums
Menu