Search results

  1. 92rohcp

    Kenne Bell A2A intercooler kit for Fox body and sn95

    top
  2. 92rohcp

    Fastest 5.0 (pushrod) Kenne Bell Mustang?

    I got you, great job in getting that all to fit nice work and I look forward to your pics.
  3. 92rohcp

    Fastest 5.0 (pushrod) Kenne Bell Mustang?

    I don't see how you mounted the 2.8L case with the longer Fox snout without going into the firewall. All the measurement I've done show the 2.8 is a 1 5/8 longer and if not moved forward would leave no room for inlet. My plan is to used a shorter 94/95 drive 1.75" shorter than the Fox and move...
  4. 92rohcp

    Fastest 5.0 (pushrod) Kenne Bell Mustang?

    Righto I've had much time to rethink my design and improve and now is the time. I went with the 205 cnc heads because TEA offers a great CNC program for the right price, but than again I could have used the 225cc or even more according to my cam builder. It's always someting and never enough is...
  5. 92rohcp

    Fastest 5.0 (pushrod) Kenne Bell Mustang?

    That was also a concern of mine. I may raising the roof in that area by extening the welded pipe all the way over to open up that area so the case outlet has more room to flow that air. You can see from my pics posted that I did bite into the that area by 1/2 inch and raised the pipe there to...
  6. 92rohcp

    Fastest 5.0 (pushrod) Kenne Bell Mustang?

    Would like to know some of your data like AIT at max power, and also what location you have your sensor in. What do you run as well for max timing or WOT timing map. Also with your throttle body on the back of the KB inlet what is your setup for reading incoming air. Are you using speed density...
  7. 92rohcp

    Fastest 5.0 (pushrod) Kenne Bell Mustang?

    I've seen the HP rating or claims by KB and you and I know they are not possible to achieve at least not on a PR. The old 2.2L was rated at suporting 68O HP and the new Big bore design 2.1 was rated at 750 these theoretical ratings are not attainable in my estimation and experience. Anyway I...
  8. 92rohcp

    Fastest 5.0 (pushrod) Kenne Bell Mustang?

    First off I'd like to say thanks for sharing all this here. I have been starved for info on a real hardcore KB guys. I too have been trying to make max power with my setup and have a very large thread on the corral that's been going for over 2 years 21 pages and 46,000 hits of my trial and error...
  9. 92rohcp

    Fastest 5.0 (pushrod) Kenne Bell Mustang?

    All good information so like me stepping up to the 2.8L is a must to attain higher power goals with a stroked PR motor. with your pulley combo your spiining your KB at near 21000 rpm at the end of your run. I'm not sure of the 2.8L but the 2.2 and 2.1 were rated by KB for max of 18000 rpm...
  10. 92rohcp

    Fastest 5.0 (pushrod) Kenne Bell Mustang?

    Yes looks like with your gonna add top end with solid lifter setup that is for sure. My cam builder said hyd liftters would start to float around 6500 and depending on your valve seat load you may be getting some there as well. No doubt you got much more power to tap into up top. Question on the...
  11. 92rohcp

    Fastest 5.0 (pushrod) Kenne Bell Mustang?

    Question for you on the 2.8L Liquid cooled is your a an H or S series the, the H being it has a jigher internal pressure 2psi and is rated for use above 15-23psi. Also could you helo me out and measure from center to center the oter bolt holes that the manifold attaches to. That is the stock...
  12. 92rohcp

    Fastest 5.0 (pushrod) Kenne Bell Mustang?

    Just got word from tinman he made the 9.54 pass with 28x10.5 slicks.
  13. 92rohcp

    Fastest 5.0 (pushrod) Kenne Bell Mustang?

    I just got word from KB tech they also confirmed the 1.5 thread pitch they however stated the strenght needs to be 12.9 class. I found a great deal here on Bolt depot. http://www.boltdepot.com/Product-Details.aspx?product=6587
  14. 92rohcp

    Fastest 5.0 (pushrod) Kenne Bell Mustang?

    Thanks my friend for all your help.
  15. 92rohcp

    Fastest 5.0 (pushrod) Kenne Bell Mustang?

    Do you buy chance know the thread pitch? I see a 1.5 and a 1.25 and if it's fine or coarse thread.
  16. 92rohcp

    Fastest 5.0 (pushrod) Kenne Bell Mustang?

    Do you mind me asking questions here or should I PM or email you further question. Are you buying your snout bolts from KB or do you source them elsewhere? A thought I had was to match or have ARP make a pulley bolt, they make the strongest bolts out there.
  17. 92rohcp

    Fastest 5.0 (pushrod) Kenne Bell Mustang?

    Any issue in mounting the old style 2.2L drive with the newer KB front cover, is it the same bolt pattern? Also did you use the same pulley bolt? I think the 5.0 units used the smaller 10mm bolt. Some have said they will break with a larger type blower like the 2.8L since the rotors are heavier...
  18. 92rohcp

    Fastest 5.0 (pushrod) Kenne Bell Mustang?

    Still great numbers on the dyno and no doubt with an auto getting accurate dyno results is hard. I to ran the HP calc and came up with your number RWHP. The pictures of the motor you posted had what looked like a older 2.2L KB, since then you pit in the LC 2.8L. I would love for you to post up...
  19. 92rohcp

    Kenne Bell A2A intercooler kit for Fox body and sn95

    Well here it goes my custom A2A 3" polished pipe kit is for sale used on my 92coupe but will fit 94-95 as well. All the T clamps and 3 ply silicone couplers go with it. Intercooler is 31x12x3 with 3" inlet and outlet. Check out my DIY thread for KB A2A if you want to know the results and see...
  20. 92rohcp

    New Fox only magazine coming out!!!

    Just paid for my subscription.
Top Bottom
Back
Forums
Menu