Search results

  1. ToplessStang

    wheel spacers

    1 inch H&R spacers on the rear of my car for the past 2 years. Drag race once or twice a week every week. Done some lapping. No problems at all to report. BEFORE AFTER
  2. ToplessStang

    Sanair show August 11

    Nice seeing you again Dave. Sorry I didn't see you when I was on my way out. Hope you enjoyed the show :nice:.
  3. ToplessStang

    Sanair show August 11

    Sunny ALL weekend. Can't wait to see that R again :hail2: .
  4. ToplessStang

    My new daily driver!!!!

    Now that is a TRUE Mustang man. Owns a Mach and buys 5.0 Stang as a daily driver :hail2: .
  5. ToplessStang

    Pic whoring once again!!!!

    NICE !!!!!!!! :nice:
  6. ToplessStang

    Should I upgrade my brakes, or just get fluid flushed and new pads?

    I got the Mach 1 brakes (same size). Worth EVERY penny. Also flushed the system while changing the front hoses.
  7. ToplessStang

    just for the heck of it...

    Piece of cake :nice:
  8. ToplessStang

    Who has installed a brake kit from BuyFordRacing.com?

    I installed my kit last fall. Both sides were leaking. I tightened some more and still leaking. I decided to keep tightening and see where I would end up. Well let me tell you I TIGHTENED it hard. Both sides stopped leaking. Hasn't leaked since that day. Good luck.
  9. ToplessStang

    How to tell if crank position sensor is bad??

    As was mentioned, if it were your crank sensor you'd most likely have driveabilty issues. Most likely wiring or the tach gauge itself. What I would try is to use the cluster diagnostic in tach mode and see if it corresponds with the needle. If the tach needle is stuck at 3 000 rpm but the...
  10. ToplessStang

    Door switch------HELP!

    It's a black connector with 2 wires that is clipped into the switch that is snapped into the latch. You have to remove the door panel to get to it. A little tip that sometimes works. Spray the latch with a good amount of WD40. Open and close the door about 20 times. It may start to work...
  11. ToplessStang

    Forza 2

    We'll have to set up a Stangnet Challenge race one of these days. Not yet though, I still SUCK :(.
  12. ToplessStang

    Hiding a shift light in the vent

    I have my Raptor installed in the vent, TRUST me you don't have to look at the vent to see it when it lights up.
  13. ToplessStang

    Leaky tie rod boots?

    Rack&pinion seals are leaking.
  14. ToplessStang

    problem w/ radiator cooling fan

    There are 3 wires that go to the motor. One of them takes a little "detour" if you will and goes into the resistor and comes out and goes to the motor. It is normal to have only two wires at the resistor. Weather you can buy the motor by itself, no clue.
  15. ToplessStang

    problem w/ radiator cooling fan

    The way it works is that on low speed the current will flow through the resistor thus reducing the current and causing the fan motor to turn at a reduced speed. At higher temps the current will go through a diffrent wire with almost no resistace (high speed). You should have 2 ORG/RD wires...
  16. ToplessStang

    problem w/ radiator cooling fan

    Ok well I stand corrected :bang: . I was looking in the Ford wiring diagram and don't see it but after mentioning your car being an 03 I went down to the garage and yup, that's a low speed resistor. That being said, if you have voltage comming out of that resistor with the A/C on and getting...
  17. ToplessStang

    problem w/ radiator cooling fan

    What year is your car? Also I've heard of low speed resistors for engine cooling fans (limits current to fan motor) but never high speed resistor. The Mustang (01-03) doesn't have a seperate engine cooling fan resistor so I have no clue what you changed :shrug:.
  18. ToplessStang

    Some stangnet LOVE..Just lowered with Pics

    Nice car :nice: .
  19. ToplessStang

    Forza 2

    Just bought a Stang and added a few stickers. I really should grow up :rlaugh: .
  20. ToplessStang

    Forza 2

    Got it today, GREAT game.
Top Bottom
Back
Forums
Menu