Search results

  1. M

    Election...Let's See How SN Compares To Nation

    Voted! McCain all the way. I know you Obama guys want change. I understand how it is these days. Look very closely into your choice. The guys has a past that stinks of old Chevys. His companions from church to dinner parties are as about as low as society has to offer. McCain and Palin will keep...
  2. M

    Painting Dashboard--How To--WARNING---Ton's Of Pic's.

    I would be very cautious about using brake cleaner. The texture of the dash can be easily melted into a smooth finish if you do not watch it. Good high percentage alcohol from the pharmacy is a safer choice for rookies. SEM that makes the paint gives specific instructions. SEM sells a cleaner...
  3. M

    Over Heating because of air

    A
  4. M

    vibration? after installing......

    Thanks
  5. M

    vibration? after installing......

    I think this constitutes an act of embarrassing him, personally. I would have told you to stick it in your pipe and smoke it as well. I read everything just fine. Anyway, back to the subject of the dowels. I purchased a new flywheel, and a new Fidanza clutch. No dowels were in the clutch or the...
  6. M

    GT40p & Mac Long tube, fitment question

    I can tell you that the Ford P Headers are very nice. The only thing, if your going to use P heads on a 351W (have to drill out the head bolt holes) then forget using the Ford P headers. They run right into the steering arm. Honestly, if I did not have all the money tied up into the heads, I...
  7. M

    How do I remove the tie rod and ball joint?

    Amazingly enough you do not need a pickle fork on most of these tapered joints. If you use a hammer to strike the sides of the steering knuckle right where the joint goes through it will drop right out. You will not damage the knuckle at all. Just keep striking it right below where the castle...
  8. M

    msd install help

    Sure there is a stock module / box. The location is on the passenger side fender wall. It is located near the bottom of the inner wall in front of the strut tower. It has an aluminum heat sink with large fins and has the plug installed in it. The module uses the aluminum to cool itself. These...
  9. M

    Start up new motor OIL???

    http://home.comcast.net/~dsmphotos/gcdc.html http://www.bobistheoilguy.com/forums/ubbthreads.php?ubb=showflat&Number=718643#Post718643
  10. M

    Start up new motor OIL???

    Perhaps the words CAUTION mean nothing to you. I did my research many moons ago. U.S. Versions of Mobil 1 and Castrol ARE NOT TRUE SYNTHETICS!! THEY CONTAIN GROUP III BASE COMPOUNDS! A PAO basestock is a true syththetic, and neither Mobil 1 or Castrol at Autozone is setup this way. European...
  11. M

    Start up new motor OIL???

    Try telling a cam manufacturer why a cam was wiped out from improper installation when you used synthetic to break it in and see what they tell you when you ask for a new one. Anyone who uses TRUE synthetics to break in an engine is just plain stupid. When you get a new cam it says "CAUTION do...
  12. M

    Start up new motor OIL???

    No it is not a myth. In order to best achieve piston ring seating for a fresh startup you need an SAE 30 or Rottella T 30. Rotella T has a higher zinc level and is better suited for cam and engine break ins. Why do you think that warranties are voided if you use a synthetic for a new car. Even...
  13. M

    Painting PVC

    Are you making an HHO generator? For gas milege?
  14. M

    Can someone help me out with my 1994 Mustang GT

    You really want to see excitement? Go get a can of Sea Foam, pull off your brake booster vacuum line, or the one near the EGR bend area of the upper intake, shove the hose in the can while running the engine revs up to around 1500 to keep it from dying, turn off engine immediately after empty...
  15. M

    Fitment questions with GT40P heads.

    I have seen that in a search a while back about the 351 Fuel pump block off. I am not sure. At my workplace I just retrieved some square stock steel from a scrap bin at work, and drilled my holes. I can tell you this though. For years at most parts stores when you requested an EGR gasket for the...
  16. M

    Fitment questions with GT40P heads.

    Yes they will, but you need to get an EGR Block Off plate as well for the upper.
  17. M

    Fitment questions with GT40P heads.

    I believe you can use the threaded nut that held on the tube to the original header, and then place a penny in it, and use it up on the EGR side. This will block the EGR and you should not have the COL at all doing this. It is when you pull the EGR off the engine you have the issue with the...
  18. M

    351 W Question

    I hit this forum when it was just in its infancy, I did not "dial up" the wrong forum. I have broadband now, back then it was dial up. So your wrong. Insults are not given, they are only taken. I stand behind my views, but am willing to adjust to anyones since my probation officer sees my every...
  19. M

    Battery Cable Vs. Welding Cable

    Heat shrink prevents the oxidation from occurring on the post. Copper, and solder will tarnish quickly and make it look like the green tone of the Statue of Liberty in a few weeks. It is not really necessary though, but your half performing the job. If your afraid of your ability to solder it...
  20. M

    Headers and GT40P Heads

    Let me save you some money, some shipping charges, time spent, and restocking fees. Do not buy anything that looks like they will fit for those heads. You have no idea what your up against. I explained it all in the other post. Let me repeat it again. No one here can tell you more than myself...
Top Bottom
Back
Forums
Menu